Epsolar Tracer-3215RN Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 36

Epsolar Tracer-3215RN Скачать руководство пользователя страница 5

1

1 Important Safety Information

Save These Instructions

This manual contains important safety, installation and operating instructions for

Tracer

The following symbols are used throughout this manual to indicate potentially

dangerous conditions or mark important safety instructions

，

please take care when

meeting these symbols

WARNING: Indicates a potentially dangerous condition.

Use extreme caution when performing this task.

CAUTION: Indicates a critical procedure for safe and proper

operation

of the controller

NOTE: Indicates a procedure or function that is important for the

safe and proper operation of the controller.

General Safety Information

Read all of the instructions and cautions in the manual before beginning installation

There are no user serviceable parts inside the Tracer Do not disassemble or attempt to

repair the controller

Disconnect the solar module and fuse/breakers near to battery before installing or

adjusting the Tracer

Install external fuses/breakers as required

Do not allow water to enter the controller

Confirm that power connections are tightened to avoid excessive heating from loose

connection

«
...
3
4
5
6
7
...
»

Содержание Tracer-3215RN





































Отзывы:

Нет отзывов