Epsolar Tracer-1206RN Скачать руководство пользователя страница 8

4

 

2.2 Optional Accessories 

Remote Meter(Model

MT-5) 

The digital remote meter displays system operating information, error indications, 

and self-diagnostics read-out. Information is displayed on a backlit LCD display. The 

large numerical display and icons are easy to read and large buttons make navigating 

the meter  menus easy.  The meter can be flush mounted in a wall or surface  mounted 

using  the  mounting  frame  (included).  The  MT-5  is  supplied  with  2m  of  cable  and  a 

mounting frame. The MT-5 connects to the RJ45 port on the Tracer. 

3 Installation Instructions 

3.1 General Installation Notes 

Read through the entire installation section first before beginning installation. 

Be very careful when working with batteries. Wear eye protection. Have fresh water 

available to wash and clean any contact with battery acid. 

Uses insulated tools and avoid placing metal objects near the batteries. 

Explosive  battery  gasses  may  be  present  during  charging.  Be  certain  there  is 

sufficient ventilation to release the gasses. 

Avoid  direct  sunlight  and  do  not  install  in  locations  where  water  can  enter  the 

controller. 

Loose  power  connections  and/or  corroded  wires  may  result  in  resistive  connections 

that  melt  wire  insulation,  burn  surrounding  materials,  or  even  cause  fire.  Ensure 

tight  connections  and  use  cable  clamps  to  secure  cables  and  prevent  them  from 

swaying in mobile applications. 

Use with Gel, Sealed or Flooded batteries only. 

Battery connection may be wired to one battery or a bank of batteries. The following 

instructions  refer  to  a  singular  battery,  but  it  is  implied  that  the  battery  connection 

can be made to either one battery or a group of batteries in a battery bank. 

 Select the system cables according to 3A/mm

2

 current density. 

3.2 Mounting 

NOTE: When  mounting the  Tracer, ensure free air through  the controller  heat 

sink  fins.  There  should  be  at  least  150mm  of  clearance  above  and  below  the 

controller to allow for cooling. If mounted in an enclosure, ventilation

 

is highly       

                            recommended.

 

WARNING: Risk of explosion! Never install the Tracer in a sealed enclose with 

flooded batteries! Do not install in a confined area where battery gas 

 

                         

can accumulate. 

Содержание Tracer-1206RN


































Отзывы: