Epsolar LS1024RPD Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 32

Epsolar LS1024RPD Скачать руководство пользователя страница 4

Contents

1 Important Safety Information .....................................1

2 General Information ...................................................2

2.1 Product Overview ................................................2

2.2 Product Features ..................................................3

3 Installation Instructions ..............................................4

3.1 General Installation Notes ...................................4

3.2 Mounting .............................................................4

3.3 Wiring .................................................................6

4 Operation ..................................................................10

4.1 PWM Technology .............................................10

4.2 Battery Charging Information ............................10

4.3 LED Indicators ..................................................12

4.4 Setting Operation ...............................................14

5 Protections, Troubleshooting and Maintenance ........17

5.1 Protection ..........................................................17

5.2 Troubleshooting ...............................................18

5.3 Maintenance ..................................................20

6 Warranty ..................................................................21

7 Technical Specifications ...........................................22

«
...
2
3
4
5
6
...
»

Содержание LS1024RPD

































Отзывы:

Нет отзывов