EPS eSoft Pro, Руководство по установке, Страница: 2 / 5

Introduction
Thank you for purchasing your eSoft Pro Water Softener. The Clack CI valve with which your water
softener is fi tted has been selected to provide the best effi ciency & performance possible.
Only
attempt this installation if you have been trained on the installation of water softeners.
Packing List
Your water softener comprises of:
Assembled eSoft Water Softener
Transformer
¾” quick connect fi ttings
Overfl ow adaptor
Installation Instructions
Firstly, the area needs to be level, have access to electricity and an open drain. Your water softener has
been designed to operate between 1.7 and 5 bar pressure. If your water pressure falls outside these
parameters it may be necessary to fi t a booster pump or a pressure reducing valve to prevent damage
to the unit. The operating temperature range of the appliance is 3°C and 45°C. Follow the instructions
supplied to connect the ¾” quick connect fi ttings.
Please observe local regulations concerning the installation of your system. Check that you have
allowed space for access to the unit for possible future maintenance. This installation may require
plumbing work and will require an electrical outlet to be fi tted near the system. If the system is
installed externally, take necessary precautions to prevent frost damage.
Inlet: This is the water supply from the mains or other. Always
install a suitable prefi lter on well water supplies.
Outlet : This is the softened water leaving the softener to
supply the rest of the house.
Drain:
This is the water used during regeneration which is
fl ushed to drain. This water will be at mains pressure and must
be taken directly to a waste-pipe with an air gap.
Overfl ow: This is used in the event of an over-fi ll of water
to the salt cabinet. This should always be taken directly to
a waste-pipe with an air gap. Install the supplied overfl ow
fi tting by drilling a 20mm hole. Its recommended to install the
overfl ow 2-3 inches below the salt lid of the cabinet.
Introduction
Thank you for purchasing your eSoft Water Softener. The Clack CI valve with which your water softener
is fitted has been selected to provide the best efficiency & performance possible.
Only attempt this
installation if you have been trained on the installation of water softeners.
Packing List
Your water softener comprises of:
Assembled eSoft Water Softener
Transformer
¾” quick connect fittings
Installation Manual
Overflow adaptor
Installation Instructions
Firstly, the area needs to be level, have access to electricity and an open drain. Your water softener
has been designed to operate between 1.7 and 5 bar pressure. If your pressure falls outside these
parameters it may be necessary to fit a booster pump or a pressure reducing valve to prevent damage
to the unit. The operating temperature range of the appliance is 3°C and 45°C. Follow the instructions
supplied to connect the ¾” quick connect fittings.
Please observe local regulations concerning the installation of your system. Check that you have
allowed space for access to the unit for possible future maintenance. This installation may require
plumbing work and will require an electrical outlet to be fitted near the system. If the system is
installed externally, take necessary precautions to prevent frost damage.
Inlet: This is the water supply from the mains or other. Always
install a suitable prefilter on well water supplies.
Outlet : This is the softened water leaving the softener to
supply the rest of the house.
Drain: This is the water used during regeneration which is
flushed to drain. This water will be at mains pressure and must
be taken directly to a waste-pipe with an air gap.
Overflow:
This is used in the event of an over-fill of water
to the salt cabinet. This should always be taken directly to
a waste-pipe with an air gap. Install the supplied overflow
fitting by drilling a 20mm hole. Its recommended to install the
overflow 2-3 inches below the salt lid of the cabinet.
1.
2.
3.
4.
5.
1.
2.
3.
4.