holder
holder
holder
junction box
in-house power cord
ceiling lock hole
ceiling lock hole
Right angle installaiton guide
http://www.lighting-epoch.co.en
http://www.lighting-epoch.co.en
Right angle installaiton guide
Before allocating luminaire, pass the in-house
power cord through the outlet hole of the
luminaire for preparing wiring.
Mounted installation guidee
Mounted installation guide
Pull the in-house power cord and pass it through
the outlet hole of the holder.
Luminaire position
Wiring luminaire with AC power cord
1
Connect the in-house AC power cord with driver's AC side.
Insert the 18 AWG AC power
cord into the close end connector
and press the end of the connector
by tools such as crimping pinchers
to insure the wires are not falling.
3
Hang up the rings of the light source onto the holder's
accessory hook.
Fasten the T-accessory with self-tapping screws.
(Use anchors and washers on concrete ceiling, take Mounted
installation guide step 2 for reference.)
Pass the in-house power cord through the T-accessory and pull
it from the outlet hole.
Allocation distance of T-accessory
Fasten the wing nut and carriage bolt on the holder's
Preliminary hole A.
Pass the in-house power cord through the outlet hole of the holder.
Put the carriage bolt set to T-accessory's ceiling lock hole a.
Adjust the holder and T-accessory location by carriage bolt set and
ceiling lock hole a, then, fasten the holder and T-accessoty with
machine screw on holder's ceiling lock hole B and T-accessory 's
ceiling lock hole b.
For the wiring installation and light source installation, take Mounted
installation guide step 3 to step 10 for reference.
Hang up the light source temporarily
Insert the wires into the wire clip in holder's side.
4
Fix the holder onto the ceiling.
2
b
a
c
d
Ceiling lock
hole diagram
5
Use tools to press the accessory hook.
6
1
2
3
4
5
6
Connect light source with driver's DC side connector.
Connect light source with driver's DC side
7
Arrange the wires and insert to the wire clip in holder.
8
Buckle up the light source's two end caps with holder.
Buckle the light source with holder
9
1
2
Push the middle of the light source until hearing a click
sound, then finishing the installation.
10
N wire
(Blue)
(Brown)
(Green)
L wire
E
arthing wire
wire clip
connector
wire clip
Tool
ex: Needle-nose pliers
Self-tapping screw
In-house power sord
T-accessory
holder
Preliminary hole A
Wing nut
carriage bolt set
Carriage bolt
Mounted T-accessory installation
Mounted holder installation
Preliminary hole B
carriage bolt set
ceiling lock hole a
ceiling lock hole b
Machine Screw
If you need to detach the light source, please press
light source's two end caps where marks the “press”.
This step is aim to wiring preparation,
not for suspended function.
Only connect with the dedicated light source as Smiley
™
series.
The close end connector applies to
18AWG AC power cord.
1
Connect
Connect
Only for U type. Right angle accessory need
to be bought in additional.
Holder
Interior
Light source installation
Light source detachment
carriage bolt set
+
=
517mm
517mm
Referring to the diagram
of “Hole on luminaire”, drill
the hole to fix the two anchors,
and screw the self-tapping
screws and washers half
into the two anchors.
Align “the two ceiling
lock hole”of the luminaire
and “two half-screwed
self-tapping screws”, and
push the luminaire up.
Move the luminaire to
be latched by the ceiling
lock hole of the luminaire.
After latching with the
ceiling lock hole, screw
the other half of self
-tapping screws, and
finish the luminaire
allocation.
Smiley™ Installation guide
(Mounted and corner installation)
epo
epo
Smiley™ Installation guide
(Mounted and corner installation)
epo
