background image

Installation Instructions

5

 

0345 27 27 810

SHOULD YOU ENCOUNTER ANY PROBLEMS 

INSTALLING THIS UNIT, CALL US ON:

energiSava

®

 325

Read and observe the guidance & safety notices listed in the Safety section

Do not remove the port covers until connecting ducting. Port covers are fitted to prevent debris falling 

into the unit and causing blockages and damage:

• The energiSava

®

 325 is designed to be 

mounted on a wall or similar. The mounting 

surface must be sufficiently strong to 

support the unit.

• Consider the positioning of electrical services 

and the condensate drain when siting the unit.

• Ensure there is sufficient access around the 

energiSava

®

 325 for future maintenance.

• Do not ‘box-in’ the unit making access to the 

unit difficult for maintenance and repair.

The unit MUST be mounted plumb and 

level front to back and side to side.

1.  Mark a horizontal line on the wall using a 

spirit level. This line will be approximately 

95mm below the location of the top face of 

the unit when fitted (excluding duct ports).

2.  Use one of the Mounting Brackets as a 

template to mark the 3 fixing hole centres.

3.  Drill holes for fixings, always use a fixing 

suited to the wall type.

4.  Fix one mounting bracket to the wall ensuring 

the interlocking side is at the top, as shown.

5.  Fix the remaining mounting bracket to 

the unit using the M6 screws and washers 

provided, ensuring the interlock side is at the 

bottom. Do not overtighten.

6.  Mount the unit by locating the two mounting 

brackets together. Ensure a positive location 

is made between the two mounting brackets.

7.  The safety bracket MUST be fitted. Fix the 

lower safety bracket as shown using the 

remaining M6 screw, washer and suitable wall 

fixing. Packing to be used as required behind 

the safety bracket to ensure unit is level.

Safety 

bracket

Hook 

onto wall 

bracket

Содержание energiSava 325





















Отзывы: