Environmental Express OAKTON EC250 Скачать руководство пользователя страница 52

Страница: 52 / 73

General set up

P5.2 Auto shut-off time setup

1. Press the

key,

P1 COND

screen appears.

2. Press the

key,

P2 TDS

screen appears.

3. Press the

key,

P3 SAL

screen appears.

4. Press the

key,

P4 DATA

screen appears.

5. Press the

key,

P5 GEN

screen appears.

6. Press the

ENT

key,

P5.1 STBL

screen appears.

7. Press the

key,

P5.2 A.OFF

screen appears.

8. Press the

ENT

key, default auto shut-off time is

30 minutes

9. Use the

keys to adjust the auto off time.

10. Press the

ENT

key,

P5.2 A.OFF

screen appears. This indicates completion of the

auto shut-off time setup.

The default shut off time is 30 minutes. This can be adjusted from 1 minute to 30 minutes. If
you set the display to ---- it indicates Auto Off is disabled. Meter will be on indefinitely till the
user switches off the meter.

Note

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание OAKTON EC250










































































Результаты поиска

Содержание OAKTON EC250

Отзывы:

Бренды по названию

Популярные бренды

Environmental Express OAKTON EC250, Инструкция по эксплуатации

Результаты поиска

Содержание OAKTON EC250

Отзывы:

Бренды по названию

Популярные бренды