Enviro E25 Series Скачать руководство пользователя

Страница: 7 / 43

WARNING:

IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A. This appliance is equipped with an ignition device

which automatically lights the pilot. Do not try to

light the pilot by hand.

B. BEFORE OPERATING smell all around the

appliance area for gas. Be sure to smell next to the

floor because some gas is heavier than air and will

settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any

phone in your building.

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

If you cannot reach your gas supplier, call the

fire department.

C. Use only your hand to push in or

turn the gas control knob. Never

use tools. If the knob will not push

in or turn by hand, don’t try to

repair it, call a qualified service

technician. Force or attempted

repair may result in a fire or

explosion.

D. Do not use this appliance if any

part has been under water.

Immediately call a qualified service

technician to inspect the appliance

and to replace any part of the

control system and any gas control

which has been under water.

OPERATING INSTRUCTIONS

1. STOP! Read the safety information above on this label.

2. Read the owner's manual including the section on

"Remote Control" operation.

3. Set the thermostat to the lowest setting.

4. Turn off all electric power to the appliance.

5. Do not attempt to light the pilot by hand.

6. Wait five (5) minutes to clear out any gas. Then smell for

gas, including near the floor. If you smell gas, STOP!

Follow "B" in the safety information above on this label.

If you don't smell gas, go to the next step.

7. Turn on all electric power to the appliance.

8. Using the remote control, set

thermostat to desired setting, or

press the ON/OFF key on the

remote. "ON" will be indicated on the

display of the remote and an audible

"beep" will be heard at the unit to

indicate the command has been

received.

TO TURN OFF GAS TO APPLIANCE

1. Set thermostat to lowest setting, or press the ON/OFF Key. "OFF" will be indicated on the display

and an audible "Beep" will be heard at the unit to indicate the command has been received.

2. Turn off all electric power to the appliance if service is to be performed.

FOR YOUR SAFETY READ BEFORE OPERATING

C-12455

9. This appliance is equipped with a

completely automatic ignition and

lighting control. The control will

attempt to light the pilot several

times if necessary. If it is

unsuccessful, it will discontinue

operations. If the appliance will

not operate, follow the

instructions "To Turn Off Gas To

Appliance" and call your service

technician or gas supplier.

Blue LCD Display

THERMOSTAT Key

ON/OFF Key

UP/DOWN Arrow Key

MODE Key

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION

MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

e25i L

ighting

anD

uRning

nstRuctions

Operating Instructions

For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating

Содержание E25 Series












































Результаты поиска

Содержание E25 Series

Отзывы:

Похожие инструкции для E25 Series

Бренды по названию

Популярные бренды

Enviro E25 Series, Руководство пользователя

Результаты поиска

Содержание E25 Series

Отзывы:

Похожие инструкции для E25 Series

Бренды по названию

Популярные бренды