Enviro E25 Series Скачать руководство пользователя страница 26

Страница: 26 / 43

Initial Installation

QUALIFIED INSTALLERS ONLY

xhaust

estRictoR

This fireplace has an internal exhaust restrictor rings. Usage of the restrictor rings is dependant on

the length of venting required and different installation requirements.

instaLLation instRuctions:

1. Plan your installation and clearances

to combustibles. The E25 may be

installed and vented into any solid

fuel fireplace that has been installed

in accordance with the National,

Provincial/State and local building

codes and has been constructed of

non-combustible materials. Also refer

learanCes

ombustIbles

section.

2. Remove door. See

aIntenanCe

anD

erVICe

- g

lass

oor

emoVal

2ft (0.6m)

Minimum

3ft (0.9m)

Minimum

Within

10ft (3m)

Roof ridge or

any other portion

of a building

Roof Clearances.

nstaLLing

the

e25:

• Remove the crate and packaging from the appliance and check to make sure there is no damage.

Carefully check the glass door. Do not use the unit if it is damaged. In the event damage is found,

please report it to your dealer as soon as possible.

• Carefully clean the fireplace and flue before installing the stove. Failure to do so may result in fumes

or soot being blown into the room and may cause a fire leading to death or serious injury.

3. Remove packaged log set and all wrapping material from the stove. Remove wrapping material from

the log set and check for any damage. If damage is observed, do not use unit and contact your local

dealer.

2.5”

2”

2.25”

The restrictor rings are installed on the exhaust

outlet The exhaust outlet is accessed from inside

of the firebox.

Remove door.

Undo the fasteners securing baffle.

Use the wing nuts provided to secure

the restrictor rings to the exhaust outlet.

Note: The E25 comes from the factory without

any restrictor rings installed.

Use the restrictor rings

at your discretion.

Be sure a clean

healthy burn is

achieved after 15

minutes of burning on

High.

Содержание E25 Series












































Результаты поиска

Содержание E25 Series

Отзывы:

Похожие инструкции для E25 Series

Бренды по названию

Популярные бренды

Enviro E25 Series, Руководство пользователя

Результаты поиска

Содержание E25 Series

Отзывы:

Похожие инструкции для E25 Series

Бренды по названию

Популярные бренды