envea PicoFlow Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 43

envea PicoFlow Скачать руководство пользователя страница 28

28

4.

Analog output

Settings and calibration of analogue output

4.1

Lower limit

Input:

0 … 22 mA

Standard: 3.2 mA

4.2

Upper limit

Input:

0 … 22 mA

Standard: 21 mA

4.3

Alarm value

Input:

0 … 22 mA

Standard: 2 mA

4.4

Alarm mode

Selection:

Alarm:

Alarm value at output, during alarm

alarm / freeze

measuring value is 0.

Freeze:

Last measurement value would be

freeze on Analogue output, till the error is

fixed.

4.5

Analogue output 1

Submenu

4.5.1 Calibration 4 mA

Selection:

The current output can be set via key

set output current

functions and adjusted at the receiving end.

4.5.2 Calibration 20 mA

Selection:

The current output can be set via key

set output current

functions and adjusted at the receiving end.

4.6

Analogue output 2

Submenu

4.6.1 Calibration 4 mA

Selection:

The current output can be set via key

set output current

functions and adjusted at the receiving end.

4.6.2 Calibration 20 mA

Selection:

The current output can be set via key

set output current

functions and adjusted at the receiving end.

«
...
26
27
28
29
30
...
»

Содержание PicoFlow












































Отзывы:

Нет отзывов