EntraPass KT-400 Скачать руководство пользователя страница 34

Страница: 34 / 47

Configuring the KT-400 Ethernet Four-Door Controller with the Web
Configuration Page

This procedure is useful if you want to configure the KT-400 in advance prior to going on site.

Note:

The KT-400 Ethernet connection must be done on port 1.

Optional Documentation

Application Note,

Networking Basics

, DN1796.

Before you start

•

The detachable

Network Configuration Information Sheet

is fully completed.

•

Determine your connection to the KT-400 and choose the appropriate network cable that you need.

1. Make sure the KT-400 is in

Forced Default Static

mode before starting the configuration. Verify the heartbeat patterns to

determine the status. See

Table 3 on page 28

for details.

2. Start your web browser and enter the following IP: 192.168.1.2 and press

Enter

Note:

Even though the KT-400 is in

Forced Default Static

mode, the

DHCP

status displays

Enable

. Make sure to change it

accordingly when entering the parameters from the

Network Configuration Information Sheet.

3. Put a jumper on

JP3

. Both jumpers should now be on

JP2

and

JP3

4. Enter the IP addresses as per the

Network Configuration Information Sheet.

5. Select a

Protocol

(

TCP

UDP

)

6. Enter a

Port

(

UDP

only)

7. Click on

Save configuration to KT-400

8. When you will go to the site with the configured KT-400, you will have to enter the same details into the EntraPass

workstation.

wwww.EntraPASS.com

8641 S. Warhawk Rd., Conifer, CO 80433 - Tel: 303-670-1099 - Email: [email protected]

Содержание KT-400
















































Результаты поиска

Содержание KT-400

Отзывы:

Похожие инструкции для KT-400

Бренды по названию

Популярные бренды

EntraPass KT-400, Руководство по установке

Результаты поиска

Содержание KT-400

Отзывы:

Похожие инструкции для KT-400

Бренды по названию

Популярные бренды