Enterasys WS-AP3705i Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

Enterasys WS-AP3705i Скачать руководство пользователя страница 10

Enterasys Wireless WS-AP3705i Install Guide

ix

About This Guide

The guide describes how to mount and connect cables to the Enterasys Wireless WS-AP3705i. In
addition, this guide provides information on the product certifications and national approvals for
the WS-AP3705i.

Who Should Use This Guide

This product should be installed and serviced by a qualified licensed technician, electrician, or
electrical maintenance person familiar with its operation and the hazards involved.

Proper

installation, which includes wiring, mounting, fusing or other over current protection and
grounding, can reduce the chance of electric shocks, fires, or explosion in this product or products
used within this product.

How to Use This Guide

Read through this guide completely to familiarize yourself with its contents and to gain an
understanding of the features and capabilities of the WS-AP3705i. A general working knowledge
of data communications networks is helpful when setting up this module.

This preface provides an overview of this guide. A brief summary of each chapter defines the
conventions used in this document and instructs how to obtain technical support from Enterasys
Networks. To locate information about various subjects in this guide, refer to the following table.

Note:

This guide does not provide information on configuration of the Enterasys Wireless APs.

For information on how to configure the Enterasys Wireless APs, see the

Enterasys Wireless

Convergence Software User Guide

.

Electrical Hazard:

Only qualified personnel should install or service this unit.

Riesgo Electrico:

Nada mas personal capacitado debe de instalar o darle servicio a esta unida.

Elektrischer Gefahrenhinweis:

Installationen oder Servicearbeiten sollten nur durch

ausgebildetes und qualifiziertes Personal vorgenommen werden.

For...

Refer to...

An overview of the WS-AP3705i features.

Chapter 1

,

Introduction

Instructions to mount the WS-AP3705i, connect cables, and
connect power.

Chapter 2

,

Installation

Specifications, environmental requirements, and physical
properties of the WS-AP3705i.

Appendix A

,

Specifications

Regulatory certifications and national approvals.

Appendix B

,

Regulatory Information

Draft

«
...
8
9
10
11
12
...
»

Содержание WS-AP3705i





































Отзывы:

Нет отзывов