entegris InVue NT6510 Скачать руководство пользователя страница 22

Страница: 22 / 36

USER GUIDE

ENTEGRIS, INC.

INVUE INTEGRATED FLOW CONTROLLERS, MODELS NT6510, NT6520

Unit Operation

Operating Environment

Storage Temperature Range

The flow controller can withstand

storage temperatures between

-15°C – 40°C (5°F –104°F) with no

permanent effect on the perfor-

mance of the device.

Operating Ambient

Temperature Range

The flow controller is designed to

operate in ambient temperature,

cleanroom environments. It is speci-

fied to operate at temperatures of

10°C–65°C (50°F–149°F). For opera-

tion above 65°C (149°F), contact

Entegris. The unit must be re-zeroed

at operating ambient temperature

conditions and after any temperature

change for the accuracy specifica-

tions to apply. See the

Maintenance

Section

on page 27 for re-zeroing

instructions.

Operating Process

Temperature Range

The flow controller is designed to

have a range of acceptable process

temperatures of 10°C –65°C (50°F –

149°F). When the process fluid is

above ambient temperatures of 23°C

(73°F), the system will experience

slight accuracy errors due to instru-

ment warm-up and changes in

viscosity and specific gravity of the

liquid. The unit must be re-zeroed

at operating process temperature

conditions and after any temperature

change for the accuracy specifica-

tions to apply. See the

Maintenance

Section

on page 27 for re-zeroing

instructions. The P8 (PFA) code

sensor interface is recom mended for

process temperatures higher than

40°C (104°F). For operation above

65°C (149°F), contact Entegris.

Positive system fluid pressure must

be maintained at all times at

elevated temperatures.

Effects of Fluid Viscosity and

Specific Gravity

The flow controller has been factory

calibrated using deionized water.

Fluids with viscosities and/or

spec ific gravity different from the

calibration fluid (water) will cause

slight accuracy errors. Correction

factors for viscosity and specific

gravity changes may be obtained

from Entegris by visiting our website

at:

www.entegrisfluidhandling.com

and following the Sensing and

Control product links.

Unit Enclosure

The standard InVue Integrated Flow

Controller cover is factory sealed

and should not be tampered with or

opened. Spray-down or temporary

immersion will not compromise the

performance of the unit.

NOTE:

Any attempt to remove,

tamper with or open the flow con

troller cover will void the warranty.

Содержание InVue NT6510





































Результаты поиска

Содержание InVue NT6510

Отзывы:

Похожие инструкции для InVue NT6510

Бренды по названию

Популярные бренды

entegris InVue NT6510, Руководство пользователя

Результаты поиска

Содержание InVue NT6510

Отзывы:

Похожие инструкции для InVue NT6510

Бренды по названию

Популярные бренды