background image

Front Panel Controls and Indicators

Each front edge indicators and switch settings are shown in the diagrams below:

Channel

ADC / TBC

Input 1

Input 2

Input 3

Input 4

Ref Pres

Remote

Local

TBC 1
TBC 2
TBC 3
TBC 4

Run

Pwr

5360

on

Remote/Local

 switch:

Set to the mode you
will be using.

Pwr

 green LED:

Indicates the presence (

ON

) or

absence (

OFF

) of power (+5V).

Run green

 LED:

OFF

A power fault or halted CPU

ON

:

A halted CPU

FAST BLINK

:

CPU Run error

SLOW BLINK

:

System OK. (If SPI control 
is active from the main
frame System Control
Module, all 

Run 

indicators

will be synchronized.)

Ch 1-4 Input 

green LEDs:

On

indicates input video signal

is present and detected on each
individual channel.

OFF

no input video signal detected

on the input of each channel.

Ref

 green LED:

On

when the external reference

source is detected.

OFF

when no reference signal is

detected.

TBC 1-4 

 switches:

Turn Time Base Correction 

On

(left)

or 

Off 

(right) for each individual

channel with the corresponding

TBC 1-4

switches.

Models 5360 and 5365 Four Channel Analog to Digital Video Converters and Embedders

5360-11

Содержание Avenue 5360

























Отзывы: