6
7
The overall purpose of this device is to receive a water meter input, and totalize the amount of water that passes through the meter. When there is flow through the
water meter, the lights flash at a rate that increases with the water flow rate. When the total amount of water flowed reaches within 10% of a pre-selected amount
the totalizer turns yellow, when the total amount reaches the pre-selected amount the totalizer turns red.
Power
This unit is to be powered using +12VDC. The power input is a wire tail with a 2.5mm, center positive barrel jack.
The totalizer has a battery backup. The battery backup uses 3 AAA size batteries. The battery holder is a part of the PCB assembly and can be accessed by removing
the lid to the cartridge filter. Battery life will vary based on water flow when running on battery mode and type of batteries used. With high continuous flow, the
batteries are expected to last approximately 14 days. With no flow the batteries are expected to last approximately 6 months.
Operation
Water Meter
The totalizer keeps track of the gallons using a water meter. The water meter is a turbine style meter with a magnetic pickup that sends a pulse to the electronics
for every revolution of the meter turbine. The meter turbine is removable for inspection and cleaning. Make sure water is bypassed or turned off when removing
the meter for maintenance. The meter has a three pin plug that connects to the electronic board.
LEDs
Normal colors for the LEDs are Green, Yellow and Red. Depending on the Totalizer value.
• Green = 0 – 90% of the programmed totalizer maximum
• Yellow = 90 – 100% of the programmed totalizer maximum
• Red >= 100% of the programmed totalizer maximum
If there is flow the LEDs should alternately turn off in the following pattern: 1-2-3-2 (repeat). The frequency that they turn off is linearly correspondent to the flow
rate being received from the water meter. For every 1 revolution from the meter, the LED pattern should be incremented to turn off the next LED. If there are no
pulse edges for 2 seconds, all the LEDs will turn on solid.
If the battery is determined to be low, the middle LED (#2) will turn White. The battery is checked only once an hour to minimize the battery drain from checking
the voltage.
Pushbutton
The pushbutton allows for the totalizer to be reset as well as the maximum value to be programmed.
To reset the totalizer, the user should press and hold the button for 3 seconds. When the totalizer is reset LEDs should flash green 3 times to confirm that it is reset.
The push button allows the unit to be programmed for the total gallons limit. It can be programmed for the range of 10,000 gals. – 990,000 gals.
To program the maximum value using the push button: Press and hold the button while powering up the board (either battery power or 12VDC power). Once the
board is powered LED 1 (left LED) will represent 100,000’s place and should be green. LED 2 (middle LED) will represent 10,000’s place and should be blue. Both
LEDs will be flashing at 1 Hz the number of flashes that corresponds to the current setting for that digit placeholder. To indicate the start of the flash sequence both
LEDs should flash white for 1 second, then flash the appropriate number of times. Once both are done wait 2 seconds and repeat. Below, Figure 1, is an example.
Serial Port
The serial port allows for quick and efficient programming through a basic terminal type interface. The board responds with a message when the enter key is
pressed:
Totalizer Current Total: 0 gallons
Totalizer Current Max. Setting: 250,000 gallons
(Send ‘r’ to reset)
( ## to enter new setting in 10,000s [valid range 0-99])
>:
Consult the manufacturer for more details on connecting to the boards serial port.
Power Monitoring and Battery Mode
The board monitors the 12Vdc power and the battery power. If there is a power failure and no batteries are installed, the current totalizer value will be saved to
non-volatile memory. When power is resumed, the totalizer count will resume from when it had previously lost power.
The LEDs should shut off during battery mode. If the totalizer is to the yellow or red state or if the battery voltage gets low, the LEDs will flash on in the appropriate
colors for 0.125 seconds every 4 seconds. If the push button is pressed in battery mode, the LEDs will turn on for 4 seconds and then return to battery mode.
WATER TOTALIZER NOTIFIER
THIS WARRANTY EXCLUDES THE FOLLOWING:
•
Damage caused by improper installation, operation or care.
•
Damage caused by chemical attack, environment, accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone, chloramines
and other related components), alteration, installation or operation contrary to the printed instructions, or by the use of accessories or components which do not meet ENPRESS’s
specifications, including the use of a replacement element not manufactured or supplied by ENPRESS LLC. Refer to the specifications section in the Installation and Operating manual
for approved application parameters.
•
Modification or alteration by other than ENPRESS LLC employees.
•
Rubber type parts and normal wear items i.e. “O” rings, etc…
•
Any costs of labor or expenses expended in the removal and/or installation of unit, or any surrounding device.
•
Altering or removing the ENPRESS LLC information label.
•
Use of non ENPRESS LLC approved cartridges, filters, or replacement parts with the appropriate systems or vessels.
•
Non-use of supported piping for plumbing connections to In/Out connections.
•
Replacement of water filter cartridge due to water pressure that is outside the specified operating range or due to excessive sediment in water supply; or replacement with non-
authorized replacement cartridge.
•
Service trips to installation site to train user on how to use product
•
Improper installation
•
Failure of product if it is abused, misused, or used for other than the intended purpose
•
Replacement of water filter cartridge due to water pressure that is outside the specified operating range or due to excessive sediment in water supply; or replacement with non-
authorized replacement cartridge
•
Damage to product cause by accident, fire, floods or acts of God
•
Incidental or consequential damage caused by possible defects with any other equipment not covered by this warranty
SPECIAL NOTICES:
•
Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after installing filter or system.
•
Systems certified for Cyst reduction may be used on disinfected water that may contain filterable cysts.
•
Any system this filter is installed in must be maintained according to manufacturer’s instructions, including replacement of filter cartridges.
•
Contaminants or other substances removed or reduced by this water filter cartridge are not necessarily in your water.
•
Note that while testing was performed under standard laboratory conditions, actual performance may vary. Systems using these filters must be installed and operated in accordance
with manufacturer’s recommended procedures and guidelines.
ENPRESS LLC- PIONEER™ System - Limited Warranty
• ENPRESS LLC warrants its line of ENPRESS PIONEER™ filtration systems, to be free of defects in material and workmanship for a period of one year, and replacement PIONEER™
filters for a limited thirty-day warranty, from the date of purchase. This warranty is extended to original purchaser, by authorized OEM customers. Use of this product constitutes Buyer’s
acceptance of this Limited Liability.
• This warranty does not cover any equipment purchased for use in applications in which the product is not suited. It is the responsibility of the buyer to determine if a product is suitable
for a particular application.
• Our obligations under this warranty are limited to the repair or replacement (at ENPRESS’s sole discretion) of the failed parts of the water treatment unit manufactured by ENPRESS, and
we assume no liability whatsoever for direct, indirect, incidental, consequential, special, general or other damages.
• We assume no liability for the determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us.
• We assume no liability and extend no warranties, expressed or implied, for the use of this product with a non-potable water source or a water source which does not meet the conditions
for use described in the owner’s guide or performance data sheet for the product.
• The warranty provided herein applies, only when used within the product specifications and service life, from the date of installation, beyond which ENPRESS LLC is absolved of any
and all liability for any use of the product. There are no other warranties, either of merchantability or fitness, either expressed or implied. Some states do not allow exclusion or limitation
of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, or country to country. To know
what your legal rights are, consult your local or state consumer affairs office, your state’s Attorney General, or your national equivalent for international users.
WARRANTY
Service under this warranty is to be provided by the distributor/installer who sold the unit to
the user. If the distributor is unable to provide warranty service, contact:
ENPRESS, LLC. | 34899 Curtis Blvd., Eastlake Ohio 44095
Phone 866.859.9274 | Fax 440.510.0202 | [email protected]
A Returned Goods Authorization (RGA) number must be received from the above office and
placed on all shipments to and in correspondence with ENPRESS LLC.
Please be prepared with the following information:
Model number
and serial number.
Date of
installation.
Name of
installer.
Nature of
problem.
Your address and
contact information
1
2
3
4
5
Figure 1
To change the maximum gallons setting, press and hold the
button for 1 second. LED1 should turn solid green, LED2
should turn off and LED3 should flash green the number of
times that corresponds to the current setting. Pressing the
button for less than 1 second would increment the value,
rolling over from 9 to 0. Below, Figure 2, is an example of the
LEDs in this mode.
Figure 2
To save the setting for the 100,000s place and begin editing
the 10,000s place press and hold the button for greater
than 1 second. LED1 should turn off, LED 2 should turn
solid blue, and LED3 should flash blue the number of times
that corresponds to the current setting. Again, pressing the
button for less than 1 second would increment the value,
rolling over from 9 to 0. Below, Figure 3, is an example of the
LEDs in this mode.
Figure 3
To save the setting for the 10,000s place and exit editing
mode and return to the mode in Figure 1 press and hold the
button for greater than 1 second. This would also save the
current setting into internal EEPROM memory.
LIMITED LIABILITY
- ENPRESS LLC makes no warranties of any kind, expressed or implied, statutory or otherwise, and expressly disclaims all
warranties of every kind, concerning the product, including, without limitation, warranties of merchantability and fitness for a particular purpose,
except that this product should be capable of performing as described in this product’s data sheet. ENPRESS LLC’s obligation shall be limited
solely to the refund of the purchase price or replacement of the product proven defective, in ENPRESS LLC’s sole discretion. Determination
of suitability of this product for uses and applications contemplated by Buyer shall be the sole responsibility of Buyer. Use of this product
constitutes Buyer’s acceptance of this Limited Liability.
