ENPC EP-PV12 Скачать руководство пользователя

Страница: 44 / 53

Disabled:

Disable the Onboard I/O CHIP’s floppy drive

interface controller. When use On-card ISA

card FDC’s controller.

Onboard UART 1:

This field allows the user to select the serial port. The default

value is 3F8H/IRQ4.

COM1: Enable Onboard Serial Port 1 and address is 3F8H/IRQ4.

COM2: Enable Onboard Serial Port 1 and address is 2F8H/IRQ3.

COM3: Enable Onboard Serial Port 1 and address is 3E8H/IRQ4.

COM4: Enable Onboard Serial Port 1 and address is 2E8H/IRQ4.

Disabled: Disable Onboard I/O CHIP’s serial port 1.

Onboard UART 2:

This field allows the user to select the serial port. The default

value is 2F8H/IRQ3.

COM1: Enable Onboard Serial Port 2 and address is 3F8H/IRQ4.

COM2: Enable Onboard Serial Port 2 and address is 2F8H/IRQ3.

COM3: Enable Onboard Serial Port 2 and address is 3E8H/IRQ4.

COM4: Enable Onboard Serial Port 2 and address is 2E8H/IRQ4.

Disabled: Disable Onboard I/O CHIP’s serial port 2.

Onboard UART 2 Mode:

The default value is standard.

This field allows the user top select the COM2 port that can

support a serial Infrared Interface.

HPSIR:

Support a Serial Infrared Interface IrDA.

ASKIR:

Support a HP Serial Infrared Interface formats.

Onboard Parallel Port:

This field allows the user to select

the LPT port. The default value is 378H/IRQ7.

378H: Enable Onboard LPT port and address is 378H and IRQ7.

278H: Enable Onboard LPT port and address is 278H and IRQ5.

3BCH: Enable Onboard LPT port and address is 3BCH and IRQ7.

Disabled: Disabled Onboard SMC CHIP’s LPT port.

3. BIOS SOFTWARE

3-8

Integrated Peripherals (Continue…)

Note: Parallel Port address is 378H/3BCH that selects the routing
of IRQ7 for LPT1. Parallel Port address is 278H that select the
routing of IRQ5 for LPT1.

EP-PV12 User’s Manual

Содержание EP-PV12






















































Результаты поиска

Содержание EP-PV12

Отзывы:

Похожие инструкции для EP-PV12

Бренды по названию

Популярные бренды

ENPC EP-PV12, Руководство пользователя

Результаты поиска

Содержание EP-PV12

Отзывы:

Похожие инструкции для EP-PV12

Бренды по названию

Популярные бренды