background image

LED Zone Controller 0-10V Installation Guide  

© 2017 EnOcean GmbH    V2.0 

 

Page  1 

 

 

Package Contents 

Tools Required 

n

 

LED Zone Controller 

n

 

Screwdriver 

n

 

Wire nuts 

 

Product Description 

The LED zone controller (LEDD) uses wireless technology to 
communicate with other self-powered EnOcean based 
products and provides an amazingly simple solution for 
dimming control of LED lighting.  
LEDD is directly supplied from the auxiliary 12V supply 
output of a connected LED driver. Its compact size enables 
flexible installation inside of or next to electrical boxes and 
fixtures so it can be easily wired out of sight using standard 
wiring practices.  
Simply link the module to an EnOcean-based motion sensor, 
light level sensor or rocker switch and experience levels of 
efficiency and convenience that can only be achieved 
through wireless controls.  
It is also possible to link LEDD to a central controller or via a 
gateway to building automation systems like BACnet. 
Product Features Include: 

n

 

Enables wireless dimming of a single fixture or a zone of 
multiple daisy chained LED fixtures (e.g. 20 each 30W or 
10 each 60W). 

n

 

Supports California Title 24 daylight harvesting scenarios, 
occupancy control and manual dimming with input from 
self-powered wireless switches and sensors. Implements 
load shedding initiated by separate Demand Response 
Controllers 

n

 

Installs inside or mounts to electrical box using threaded 
connector 

n

 

Supports wireless remote commissioning to link devices 
and set parameters

 

Specifications (typ. values) 

Power Supply 

11.0 V – 13.2 V DC 

Supply Current (typ)  16 mA @12VDC supply (no sourcing) 

38 mA @12VDC supply  
(10V/20mA sourcing) 

Power Consumption  < 200 mW @ 12 V DC  

(excluding 0-10V sourcing power) 

< 460 mW @ 12 V DC  

(at maximum 0-10V sourcing power) 

0-10V output 

Tole3%/-4% (1-10V range) 

Current sourcing / sinking 20 mA*

 

* F

or high sinking current and dim value settings 

below 1V, the output voltage may exceed the 
selected output value and reach 1V max.

 

Inputs/Outputs 

Flying-lead style wires: 

n

 

2 power input wires 

n

 

2 output wires for 0-10V control 

Local User Interface  2 Buttons, 1 LED for device    

configuration & manual control 

RF Standard 

EnOcean 902 MHz (LEDRU) 

Transmission Range  80 ft. (25 m) 
EnOcean Equipment 

Profile 

D2-40-00 with RECOM 
Compatible with Navigan™ 

Interoperable 

Products / EEPs 
(EnOcean 
Equipment Profiles) 

 

Rocker Pad Switch (F6-02-02) 

Occupancy Sensor (A5-07-01) 
Occupancy Sensor (A5-07-02) 
Occupancy Sensor (A5-07-03) 
Light Level Sensor (A5-06-02) 
Light Level Sensor (A6-06-03) 
Central Controller (A5-38-08) 
Demand Response (A5-37-01) 

Dimensions 

2.24” H x 1.65” W x 1.2” D 
(57mm x 42mm x 30mm) 

Weight 

2.5oz. (70g)

 

Mounting 

n

 

Connect to electrical boxes and   
fixtures using threaded nipple 

n

 

Install inside standard electrical box 

Environment 

n

 

Indoor use only 

n

 

32° to 140° F (0° to 60° C) 

n

 

20% to 95% relative 
humidity  (non-condensing) 

Agency Compliance  FCC, IC 

UL 2043 plenum rated 

 

 

 

Содержание LEDD









Отзывы: