The Menu LED or Set LED display solid for a number of sec
-
onds in a certain color to indicate a mode or a confirmation.
The Menu LED blinks a number of times in a color to indi
-
cate a selected menu.
The Set LED blinks a number of times in a color to indicate
an option.
A number in a white box indicates the number of times to
click the Menu button or Set button.
A number in a black box indicates the number of seconds to
hold down the Menu button or Set button.
To link a transmitter to a transceiver
1. Access Basic Setup mode.
NOTE:
By default, the Accept Link option in the Linking
menu is selected. Once activated, this option stays active for
two minutes to provide time to link multiple devices.
Ready to accept links.
2.
For the transmitter to be linked, do one of the following ac
-
cording to the type of device:
A.
Sensor: click the designated link button.
B.
Key Card Switch: insert/remove the card 3 times quickly.
C.
Rocker Pad: click the top button 3 times quickly.
Device linked successfully.
Set LED displays solid
green for 3 seconds.
The relay will toggle once to indicate a successful learn in.
After a device is linked, additional learn telegrams from
that device will cause the relay to toggle once.
Ready to accept new links.
3.
To exit mode and return to normal operation, press and hold
both buttons for 2 seconds.
To unlink a device
Follow the same steps as described in the “To link...” section
above with the following deviations:
▪
After step 1 in the “To link...” section above, click the “Set”
(right) button 3 times to enable the “Remove Link” option.
Ready to remove links.
▪
Follow the same instructions as shown in Step 2 of the “To
link...” section. The Set (right) LED will turn red briefly to indi
-
cate the link was successfully removed.
To restore factory defaults
Follow these steps to clear all linked devices and restore the In-
line Switch Module to its factory default settings.
1.
Press and hold both buttons for 15 seconds
Hold buttons until the Menu (left) LED is solid RED and the
Set (right) LED is solid Amber (Both LEDs will turn various
colors as the module cycles through the resetting process.
2.
Press and hold the Set (right) button for 3 seconds to con
-
firm factory reset.
3.
Device will reboot.
Configuring
The default settings on the module support common control
and installation scenarios. However, some occupancy settings
can be adjusted on the module using the setup interface, if
required.
Setting
Default
Application
Auto-On
Automatically
Determined
If linked to an occupancy sen
-
sor, the default is Enabled.
If linked to a switch, the default
is Disabled for manual control.
Vacancy Check
15 minutes
If linked to a occupancy senor
and a door sensor.
Switched Auto-Off
Disabled
If linked to a rocker pad or key
card switch.
Motion Auto-Off
15 minutes
If linked to occupancy sensor.
Door/Window Ajar
2 minutes
If linked to a window sensor or
patio door.
Egress
30 seconds
If linked to a key card switch.
Auto-Off
There are two auto-off menus, one for occupancy sensors,
and one for rocker switches. For linked occupancy sensors,
the default is 15 minutes. For
linked rocker pads and key card
switches, the default is Disabled
to allow manual control.
From the auto-off timer menu,
the active option is indicated by
the number of green blinks on
the Set LED; amber blinks indicate
an unsaved change. Click the Set
button an appropriate number of
times to select an option.
To change the switched auto-off option:
This example shows changing the option from Disabled to 5
minutes.
1. Access Basic Setup mode.
Option
Clicks Blinks
Disabled
5 mins.
15 mins.
30 mins.
60 mins.
In-line Switch Module • Installation Guide
Page 3
© 2015 EnOcean GmbH
