enmco PT16FM Скачать руководство пользователя страница 8

TOT

---- Total hours of operation.

JOB

---- Hours of operation since the timer was reset.

b)  Press and hold the "

SET

" button until 

display shows "

RPM

" icon and alert RPM 

numerical value starts flashing.

c)  Press "

SET

" or "

MENU

" button until you 

get desired alert RPM numerical value, 

release the button, the LCD will flash for 10 

seconds and return to "

TOT

" (total hours). 

d)  If the alert RPM numerical value is set to 

OFF, which means that the alert RPM 

function is closed.

a)  This is always displayed when engine is off. (DSP-1 SYSTEM)

To view "JOB" time:

 Press the "

MENU

button once.

To reset "JOB" time:

 Press and hold the 

"

SET

" button until display shows "

0000:00

starts flashing, then release the "

SET

" button, 

the "

JOB

" display will reset to "

0:00

", and you 

will begin to record the next job interval.

b)  Total hours can not reset.
c)  The total hours max value is 999999; When the total hours range is 

0.0-9999hours59min, the timing accuracy is 1min; When the total hours 

range is 9999hours59min-99999.9hours, the timing accuracy is 0.1H; 

When the total hours exceeds 99999.9hours, the timing accuracy is 1H.
d)  When the total hours exceeds 999999hours, the timing will restart from 

0.

Press the button 

3 times

Press the button 

once

Press and hold

the button for 2S

Press and hold

the button for 2S

(1234Hours 56Minutes)

6

7

Содержание PT16FM











Отзывы: