enmco PT16FM Скачать руководство пользователя страница 6

3. The function and operation under the DSP-1 system

Engine 

firing 

patterns

1P1R

1P2R

2P1R

3P1R

3P2R
4P1R
5P2R

6P1R

8P1R

4 stroke 2 cylinder

4 stroke 1 cylinder
4 stroke 4 cylinder
2 stroke 2 cylinder

4 stroke 6 cylinder
2 stroke 3 cylinder

4 stroke 3 cylinder
4 stroke 8 cylinder

4 spark per revolution

5 spark 2 revolution

8 spark per revolution

6 spark 

per revolution

4 stroke 5 cylinder

4 stroke 12 cylinder
2 stroke 6 cylinder

4 stroke 16 cylinder

1 spark 

per revolution

1 spark 2 revolution

2 spark 

per revolution

3 spark 

per revolution

3 spark 2 revolution

25000

25000

12500

8000

16000

6250

10000

4000

3125

2 stroke 1 cylinder

Engine type

RPM 

Capacity

Spark plug 

firing and engine 

rotate laps

RPM 

---- Typical RPM display during operation of the engine

Programmable firing patterns

 

---- Determined the amount 

of pluses(sparks) per engine revolution.

a)  When the tach hour meter detect the engine spark plug signal for 

more than 1s continuously, the LCD will display the current RPM of 

the engine.
b)  The RPM will be refreshed every 0.5s.
c)  The RPM can be programmed for different pulses per revolution; 

Different programming setting will get different RPM; Please follow 

the instructions in section 2 below to programming setting for 

accurate programming.

This product provides 9 programmable firing patterns, which can be 

selected according to the corresponding relationship in the table below.

Note: Some 4 stroke 1 cylinder engine is 1P1R, the setting is the same 

way as the 2 stroke 1 cylinder engine.

1

2

DSP-1 to DSP-2

Press and hold 

Содержание PT16FM











Отзывы: