background image

 

6

 

  Corn must be clean and free from debris; never burn corn strait from the field.  Stalk 

parts, excessive fines and cob remnants, etc. will clog the auger mechanism.  We highly 
recommend the use of a sifter; sifters to filter your corn are available from dealers (and 
we offer a sifter at 

www.englanderstoves.com

).  Damage caused by dirty and/or 

unfiltered (unsifted) corn is not covered by the product warranty – ask for and use clean 
filtered bagged corn only. 

 

 

DISCLAIMER NOTICE: 

No guarantee is made regarding the heating capacity of this 

product. The actual area that this unit will heat depends on factors such as building 
conditions, heat loss, type of construction, amount and type of insulation, type of air 
movement and heat distribution, and the location of the product. 

 

 

Important:  

Your home must be checked to verify that there is no negative pressure that 

will affect the operation of this appliance.  

 

 

IMPORTANT:  DO NOT BURN “TREATED” SEED CORN IN YOUR STOVE.

 Seed corn 

is treated with chemical pesticides that are harmful or fatal if swallowed; therefore, seed 
corn is dangerous to have in the house, especially where children can reach it.

 Burning 

treated seed corn in your stove will void your warranty and will destroy the 
exhaust system on the unit.

 

 

  There are many varieties of corn grown around the world. Each variety has unique 

characteristics including the shape and size of the kernel. Your stove will burn more 
consistently with a small to medium kernel corn.  If the kernel size of the corn varies 
greatly or if you switch sources frequently, you will get a less consistent burn.

 Do not 

use corn with high wax content.  

 

  Vacuum the hopper out after every 6-8 bags to eliminate buildup of saw dust and fines 

from corn. 

 

Содержание 10-CDV
































Отзывы: