~61~
Technical Specifications
Electrical Specifications
Base Station
Portable Handset
Frequency
915-928 MHz
915-928 MHz
RF Output Power
Peak: 27 dBm
Average: 21 dBm
Peak: 26 dBm
Average: 20 dBm
Channel Spacing
101 kHz
101 kHz
Number of Channels
126
126
Modulation
Differentially Encoded MSK
Differentially Encoded MSK
Multiple Access
Frequency Hopping TDD
Frequency Hopping TDD
Frequency Hopping Rate
100 per second
100 per second
TDD Frame Length
10 ms
10 ms
Number of Slots/Frame
4
4
Receiver Sensitivity
<-111dBm (@ BER 10-2)
<-111dBm (@ BER 10-2)
Antenna Gain
2 dBi
Long: 2.5 dBi; Short: 1.5 dBi
Antenna Connector
Reversed TNC
Proprietary
Telephone Interface
RJ11 x 2
NA
Channel Coding
8 kbps Convolu CRC
8 kbps Convolu CRC
Transmission Data Rate
85.333 kbps
85.333 kbps
Speech Coding
8 kbps G.729AB
8 kbps G.729AB
User Data Rate
64kbps duplex
64kbps duplex
Duplex
Time Division Duplex (TDD)
Time Division Duplex (TDD)
Number of System ID
65,536
65,536
Ring Signal
20-50 Hz, 30-90 Vrms
NA
Flash Time
100-900 ms programmable
NA
Power Source
AC/DC 5V/1A Adapter
3.7V/1100mAh Li-Ion Battery
550mA
Charger Current
NA
(550/850mA for desktop
charger)
Charge Time
NA
3hours
Regulation Compliance
FCC Part 15, Part 68
ACMA Compliant
FCC Part 15, Part 68
Hearing Aid Compatible
ACMA Compliant
Operating Temperature
0 – 50 °C
-10 – 60 °C
Storage Temperature
-40 – 70
°
C
-40 – 70
°
C
Humidity
20 – 75 %
20 – 75 %
Notes:
1.
NA = Not Applicable.
2.
The manufacturer reserves the right to change designs and specifications without
notice.
~62~
FCC Part 68 Statement
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the bottom of SN933 base station
is a label that contains,
among other information, a product identifier in the format US:
SNIW403BFS2. If
requested, this number must be provided to the telephone company.
Applicable connector jack Universal Service Order Codes (“USOC”) for the
Equipment is RJ11C.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US:
SNIW403BFS2. The digits
represented by 0.3 are the REN without a decimal point (
e.g.
, 03 is a REN of 0.3).
If this SN933
causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required.
But if advance notice isn't practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations
or procedures that could affect the operation of the equipment. If this happens
the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this SN933
,
for repair or warranty information, please
contact:
Company:
Aristel Networks Pty Ltd. www.aristel.com.au
Address: 1/25 Howleys Road,
Notting Hill, Victoria, 3168.
