ENFORCER Multi-Color LED Strobe Light
SECO-LARM U.S.A., Inc.
3
Configuring LED Color and Strobe:
1.
Decide where the LED strobe light is to be mounted.
Use a pencil to mark the location of the two mounting
screws.
2.
Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and power (brown) wires through the wall.
NOTE:
For surface wiring applications, remove the
thinned-out slot with a pair of pliers.
3.
Connect the wires to their respective locations on an
alarm control panel or other security panel.
4.
Remove the lens and mount the LED strobe light to
the surface using the two included mounting screws
with rubber “O” rings.
If screws are fastened too
tightly, the “O” rings will be damaged.
5.
Select the color and strobe setting using the DIP
Switches (see chart below for details) and adjust
the speed using the strobe speed control (clockwise
to increase, counterclockwise to decrease).
6.
Replace lens.
If lens is fastened too tightly, the
“O” ring will be damaged.
Installation:
IMPORTANT:
Disconnect power before adjusting DIP switches.
B1 B2 G1 G2 R1 R2
Trigger Mode
•
Before starting, please read this manual carefully and keep it for future reference.
•
Be sure to use the LED strobe light within the given electrical limits.
Power ON Mode
1.
Decide where the LED strobe light is to be mounted.
Use a pencil to mark the location of the two mounting
screws.
2.
Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and trigger (blue, green, red) wires through the wall.
NOTE:
For surface wiring applications, remove the
thinned-out slot with a pair of pliers.
3.
Connect the wires to their respective locations on an
alarm control panel, other security panel, or trigger
device according to the color desired (see chart below).
4.
Remove the lens and mount the LED strobe light to
the surface using the two included mounting screws
with rubber “O” rings.
If screws are fastened too
tightly, the “O” rings will be damaged.
5.
Set the LEDs to "strobe" or "steady ON" via the
jumper, and adjust the strobe speed using the
strobe speed control (clockwise to increase,
counterclockwise to decrease).
6.
Replace lens.
If lens is fastened too tightly, the
“O” ring will be damaged.
Default DIP Switch Setting
:
Red strobe
Color
Strobe Setting
LED
Jumper
DIP Switch
Configuration
Trigger Wire
Connections
Red
LEDs strobe continuously
Strobe
R2 ON only (default)
Connect red wire to GND
LEDs are steady ON
Steady ON
R1 ON only
Green
LEDs strobe continuously
Strobe
G2 ON only
Connect green wire to GND
LEDs are steady ON
Steady ON
G1 ON only
Blue
LEDs strobe continuously
Strobe
B2 ON only
Connect blue wire to GND
LEDs are steady ON
Steady ON
B1 ON only
Cyan
LEDs strobe continuously
Strobe
G2 and B2 ON
Connect green and blue
wires to GND
LEDs are steady ON
Steady ON
G2 and B2 ON
Magenta
LEDs strobe continuously
Strobe
R2 and B2 ON
Connect red and blue wires
to GND
LEDs are steady ON
Steady ON
R2 and B2 ON
Yellow
LEDs strobe continuously
Strobe
R2 and G2 ON
Connect red and green
wires to GND
LEDs are steady ON
Steady ON
R2 and G2 ON
White
LEDs strobe continuously
Strobe
R2, G2, and B2 ON
Connect all three trigger
wires to GND
LEDs are steady ON
Steady ON
All ON
NOTE:
For Trigger Mode, LED
strobe and steady on setting is set
with jumper, see
Overview
(pg. 2).
