ENFORCER 200H
Owner's Manual
ENFORCER 200H
Owner's Manual
The starter disable prevents the car from
being started.
If the shock sensor detects light taps on the
car, it will trigger the pre-intrusion alert
(the siren chirps three times and the
parking lights flash three times) to warn
potential thieves and vandals. However, if
the shock sensor detects a strong shock to
the car, such as shock caused by prying
the trunk open, it will trigger the alarm for
30 seconds. (See DUAL-STAGE SHOCK
SENSOR, page 8.)
While your alarm is armed, your car is
protected in the following ways:
Potential thieves or vandals will be
deterred by the flashing LED.
If anyone opens a door, the alarm will
immediately sound the siren and flash the
parking lights for 30 seconds, after which
the alarm will rearm, bypassing any open
doors.
Turning the ignition key ON will trigger the
alarm for 30 seconds.
TOTAL PROTECTION
DISARMING
There are times, especially at night, when you
may not want to hear the siren chirps. There
are 2 ways to delete chirps:
A.
One-time delete
— Just press button #2
any time before you need the chirps
deleted. For instance, press button #2
before you press button #1 to arm or
disarm the alarm, and the chirps will not
sound, but the parking lights will still flash.
The chirps are restored the next time you
press a transmitter button.
B.
Permanent delete
— Your dealer can
program your alarm to delete the chirps
on a permanent basis.
CHIRP DELETE (silent arm/disarm)
If you lose your transmitter, you can disarm
your alarm with the ignition key and “VEPLe”
switch. While your alarm is either armed or
triggered, turn the ignition switch ON. Within
15 seconds, press and release the VEPLe
switch 3 times. The siren and the flashing
EMERGENCY DISARM
lights stop if the alarm was
triggered, and then chirp and
flash three times. The alarm is now in valet
(see VALET on page 7). Ask your dealer
where the switch is hidden.
NOTE — Either method deletes the arm,
disarm, pre-intrusion, zone bypass, sensor
bypass, emergency disarm, valet, and tamper
chirps. However, it does not affect the
flashing parking lights.
→
→
→
→
Page 7
Page 6
SECO-LARM U.S.A., Inc.
To disarm the alarm, press button #1. The
siren chirps twice, the parking lights flash
twice then turn steady ON for 6 seconds (or
until you turn the ignition ON), and the LED
turns OFF. What happens next depends on
how your alarm is set (ask your dealer):
Alarm set for active arming with
permanent disarm
The alarm is now completely disarmed.
Alarm set for active arming with
automatic rearm
The system will enter arming mode. If a
door is opened, the system
is permanently disarmed.
Alarm set for
passive arming
with automatic
rearm
The system will enter arming mode. If a
door is opened, the system is only
temporarily disarmed. Closing the open
door will cause the alarm to re-arm 30
seconds later. To fully disarm the alarm,
turn the ignition ON while the door is
opened, or within 30 seconds after closing
the door.
VALET
Sometimes you may not wish your alarm to
arm when you leave your vehicle. (For
instance, if you leave your car with a valet
attendant, you may not want to teach him
how the alarm operates.) If your alarm is set
for active (manual) arming, this is easy —
don’t press button #1, and the alarm will not
arm. However, if your alarm is set to arm
passively, use the valet mode to prevent it
from arming.
To enter valet, first disarm the alarm and turn
the ignition ON. Within 15 seconds, press
and release the VEPLe button 3 times. The
alarm is now in the valet mode. The siren
chirps and the parking lights flash once to
confirm. (Your alarm also goes into valet
when you use emergency disarm. See
EMERGENCY DISARM on page 6).
To exit valet, just turn the ignition ON and,
within 15 sec., press and release the VEPLe
button 3 times. The siren chirps twice and
the parking lights flash twice to confirm valet
is exited and that the alarm is now disarmed.
If you press transmitter button #1 while the
alarm is in valet, the doors will lock or
unlock, and the parking lights will flash four
times. The alarm's emergency call for help
and the 2nd channel output operate
normally.
DUAL-STAGE SHOCK SENSOR
Your alarm includes a patented dual-stage
shock sensor.
The first stage (pre-intrusion alert) warns
thieves the alarm is armed. For instance, the
alarm will chirp three times and the parking
lights will flash three times if the sensor detects
a light bump to the vehicle. However, if the
thief attacks the car with sufficient force, the
alarm will trigger. (Your dealer can make the
shock sensor more or less sensitive to attack,
depending on your vehicle.)
NOTE — The shock sensor will not be ready
to trigger the alarm until three seconds after
the alarm is armed.
