background image

ENFORCER 200H 

Owner's Manual

ENFORCER 200H 

Owner's Manual

Page 8

SECO-LARM U.S.A., Inc.

A. Enabling the ANTI-CARJACK function:

If the ANTI-CARJACK toggle switch is not
installed, you cannot use the ANTI-
CARJACK function (please ask your
dealer).

To enable the ANTI-CARJACK
function, put the ANTI-CARJACK
toggle switch to the ON position.
If the ANTI-CARJACK toggle switch is OFF,
the ANTI-CARJACK function cannot be
entered.

Once the ANTI-CARJACK function is
enabled, you can disable it by turning the
ANTI-CARJACK toggle switch OFF.
However, this must be done before you
turn the ignition ON.

B. Stages of the ANTI-CARJACK mode:

1. Stage 1

a. ANTI-CARJACK is triggered if

someone opens and closes a door
while the ignition is ON or opens
and closes a door and then turns
the ignition ON.  Once ANTI-
CARJACK is triggered, turning
OFF the ANTI-CARJACK toggle
switch will have no affect.  At this
point, Stage 1 begins.  Stage 1
lasts for up to 30
seconds.

b. During the 30

seconds, the LED is
steady ON.

c. Pressing the VEPLe

switch one time during
the 30 seconds exits
ANTI-CARJACK.  Once ANTI-
CARJACK is exited, the LED turns
OFF.

d. If the ignition is switched OFF at

any time during the 30 seconds
without first pressing the VEPLe
switch, Stage 1’s 30-second
countdown will pause, but ANTI-

ANTI-CARJACK PROTECTION

CARJACK will not exit.  The LED
will turn OFF.  The next time the
ignition is turned ON, Stage 1’s
30-second countdown will pick up
where it left off.

2. Stage 2

a. Once Stage 1 ends,

Stage 2 begins.  Stage
2 also lasts for up to
30 seconds.

b. While in Stage 2, the

LED remains steady ON, the
parking lights flash,
and the siren
continuously chirps.

c. Pressing the VEPLe

switch at any time during this
stage exits ANTI-CARJACK
provided the ignition is still ON.
(If the ignition is turned OFF
before pressing the VEPLe switch,
the alarm jumps to Stage 3, see
below.)  Once ANTI-CARJACK is
exited, the lights stop flashing, the
siren stops chirping, and the LED
turns OFF.  The alarm can now be
used as normal.

3. Stage 3

a. Once Stage 2 ends,

Stage 3 immediately begins.

b. While in Stage 3, the LED remains

steady ON, and the parking lights
continue to flash.  However, the
siren sound changes from
chirping to a full blast (sound
continuously).  The lights flash and
the siren sounds until the
emergency disarm procedure is
performed or until 30 seconds
after the ignition is turned OFF.

c. The starter disable output is

engaged.  This means that turning
the ignition OFF or pressing the
VEPLe switch one time will have no
affect.   The emergency disarm
procedure must be performed in

When you press button #1 to arm the alarm,
and the alarm responds with three chirps and
three light flashes, there are two possibilities:

A. Delayed domelights — If your domelights

do not immediately turn OFF when you
close your car door (in other words, your
vehicle has delayed domelights), this is
normal.  The alarm should protect all the
openings once the domelights go OFF.

B. A zone was bypassed — In other words,

the alarm has armed, but a door may not
be protected (either because it is open, or
because its pin switch is broken).  If the

ZONE BYPASS

bypassed door is later closed, it will be
restored.

If your alarm indicates a bypassed zone, find
the cause as soon as possible to ensure your
vehicle is completely protected.  For instance,
if your driver's door is not properly closed
when you arm your alarm, a thief may be
able to open any door without setting off the
alarm.

NOTE — The chirps to confirm zone bypass
will not sound if chirp delete is engaged.
However, the parking lights will still flash three
times.  See CHIRP DELETE, page 7.

To trigger the alarm in an emergency, press
and hold transmitter button #1 for 3 seconds.
The siren sounds and the parking lights flash
for about 30 seconds.  Stop the siren and the
parking lights any time by pressing button #1
again.

EMERGENCY CALL FOR HELP (PANIC)

If the alarm was disarmed
when you triggered the
emergency call for help, the
alarm immediately arms and
the doors lock.  If the alarm was
armed, the opposite will occur.

SENSOR BYPASS

This feature lets you turn off the Dual Stage
Sensor and any other auxiliary sensors
included with your ENFORCER system, while
leaving the rest of the alarm armed.  This is
useful at places like airports or parking
structures where there may be excessive
vibration causing your system to trigger
inadvertently.

Should you wish to bypass your alarm's
sensors, first press button #1 to arm the
alarm (even if the alarm is set for passive
arming).  The siren chirps and the parking
lights flash once (three times if a zone is

bypassed) to confirm armed.  Within three
seconds, press button #2.  The siren chirps
three times and the parking lights flash three
times to confirm sensors are bypassed.  The
sensors are automatically restored the next
time button #1 is pressed.

NOTE — The chirps to confirm zone bypass
will not sound if chirp delete is engaged.
However, the parking lights will still flash three
times.  See CHIRP DELETE, page 7.

Page 5

         →

      →

   →

Содержание 200H







Отзывы: