INSTALLATION
NSTRUCTIONS
WARRANTY INFORMATION
©
2016
Enerwave Home Automation ●
WWW.
ENERWAVEAUTOMATION
.COM
● CA, USA
Model: ZWN-
B
DS
-
PLUS
Wireless Home Automation Control Device
Ceiling mounted PIR Motion Sensor
020
9
1600
5
4
-0
2
INSTALLING Z-WAVE DEVICES
LOCATIONS
Installation of Z-Wave devices instantly increases the functionality, efficiency, and value of your home. The more devices you install, the more efficient your house will be.
The most effective
locations to install Z-Wave devices are in the Living Room, Bedrooms, Kitchens, Family Rooms, Guest Rooms, and Entertainment Rooms.
This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 100 feet. Actual performance in a home depends on the numbers of walls between the remote
controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. Z-Wave devices act as signal repeaters ONLY after
they are "Included" on the network.
This device's signal repeater is disabled, however uses repeated signals from other Z-Wave devices to increase it's signal range.
This device is warranted to be free of material and workmanship defects for 2 years from the date of
purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty
claim. ALL claims must be verified and approved by
Enerwave
, Inc. Warranties from other
Enerwave
products may vary. This warranty is nontransferable and does not cover normal wear and tear or any
malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper
installation. To the fullest extent permitted by the applicable state law,
Enerwave
shall not be liable to the
purchaser or end user customer of
Enerwave
products for direct, indirect, incidental, or consequential
damages even if
Enerwave
has been advised of the possibility of such damages.
Enerwave
’ total liability
under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair,
replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
DESCRIPTION
The
ZW
N-
B
DS
-
PLUS
is
a
Door/ Window
Sensor
with Z-Wave technology
.
This sensor
can be used to turn on devices that are connect
ed
to the same Z-Wave network
. For the
advanced users, the functions are programmable for setting scenes, associations and
scheduling events.
The sensor can be programmed to turn on lights, run the thermostat,
and notify operator(s) of an open door/ window or armed sensor.
FEATURES
•
No wiring required. Battery operated.
•
Remotely
control of any load
connected to a Z-Wave device on the network.
•
Reduce energy consumption and enjoy wireless home automation
.
•
Supports Z-Wave associations, sending commands up to 5 associated Z-Wave devices
•
Low Battery warning.
REQUIREMENTS
Z-
Wave devices require a connection to a compatible hub. Once the device is properly
added to the hub, it can be managed and customized to your needs. Please visit
www.enerwaveautomation.com for a list of compatible hubs.
SPECIFICATIONS
Z-Wave Frequency.............................................................................. 908.42 MHz
Operating Temperature........................................................................... 32-104° F
FCC COMPLIANCE STATEMENT
FCC Grant of Equipment Authorizations of this device and transmitters installed in this device can be found at FCC website by entering the FCC ID number on the device.
Caution:
C
hanges or modifications not expressly approved by the part responsible for compliance could void the user’s
right
to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation of the device.
T
his equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Read and understand these instructions before installing.
Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance so an unintentional activation may occur if the wrong button
on the remote is pressed. Z-Wave devices can be automatically powered on by programmed events. Unattended or unintentional operation could result in hazardous conditions. Z-Wave enabled devices should never be used to supply power to, control
,
or monitor medical and/or life
support equipment.
NEW
Z-WAVE 500 SERIES
FEATURES
−
Three RF channels for improved noise immunity and higher bandwidth
−
New Plug-n-Play Network-wide Inclusion feature
−
Improved self-healing and fault tolerance with Explorer Frame feature
−
Standardized method for Over the Air firmware updates (OTA)
−
Improved product information capture for product certification database
−
50% improvement in battery life
−
67% improvement in range
−
250% more bandwidth
−
Fully backward compatible
Power Supply
.............
......................
.....................
....
..
...
.
1 Lithium CR2 3V
Batter
y
