Instruction Manual for MODEL EDI62S
Instruction Manual for MODEL EDI62S
1/12
ED-34828
2008.10
1
Before Using the Unit
Thank you for purchasing our quality designed and manufactured EDI62S
Series. Before unpacking the unit, check for damages during transporta-
tion. If you have noticed any damage, directly contact us or our distribu-
tor.
1.1 Type Identification
Each model number of the EDI62S series has its general specifica-
tions, and the following describes each note and the meaning. Before
using the unit, check that the model number and specifications of the
delivered unit match those of the product you ordered. For optional
units, see the separate instruction Manuals.
1.2 Accessories
2
Mounting Method
2.1 Panel Cut Size
Cut the panel to mount the EDI62S series in accordance with the
illustration below:
The recommended panel thickness is 0.8 to 5.0mm.
2.2 How to Mount the Unit on the Panel
Mount the EDI62S series to the panel in accordance with the illustra-
tion below:
3
Terminals and Connections
3.1 Power supply connections
3.2 Input Signal Connections
3.3 Comparator Output Connections
Each unit is not replaceable by the customer.
Caution
！
⑤
AC POWER
⑥
AC POWER
③
NC
④
NC
①
NC
②
NC
⑤
NC
③
NC
④
NC
①
DC POW(+)
②
DC POW(-)
⑥
NC
Top
Bottom
5.8 mm or
less
5.8 mm or
less
Suitable solderless terminals
AC pow er supply
DC pow er supply
(1) Remove the mounting band and insert the case
from the front of the panel.
(2) Fix the case using the mounting band from the
rear of the panel.
(1) T h e r e c o m m e n d e d p a n e l t h i c k n e s s i s 0 . 8 t o 5 m m .
(2) D o n o t i n s t a l l t h e u n i t i n lo c a t io n s w h e r e i t is e x p o s e d t o d ir e c t s u n l i g h t ;
w h e r e a m b i e n t e m p e r a t u r e o r h u m i d i t y d o e s n ' t m e e t t h e r e q u i r e m e n t s b e l o w ;
o r w h e r e a d r a s t i c c h a n g e i n t e m p e r a t u r e m a y a u s e c o n d e n s a t i o n .
A m b i e n t t e m p e r a t u r e : 0 t o 5 0
℃
A m b i e n t h u m i d i t y : 3 5 t o 8 5 %
(3) D o n o t i n s t a l l t h e u n i t w h e r e i t i s e x p o s e d t o d u s t , p a r t i c l e s , c h e m i c a l s h a r m f u l t o
e l e c t r i c c o m p o n e n t s , c o r r o s i v e g a s e s , e t c .
(4)
D o n o t i n s t a l l t h e u n i t w h e r e i t i s e x p o s e d t o e x c e s s i v e v i b r a t i o n o r s h o c k .
(5)
I n s t a l l t h e u n i t h o r i z o n t a l l y ; o t h e r w i s e , v e n t i l a t i o n w i l l b e a d v e r s e l y a f f e c t e d a n d
m a y r e s u l t i n d e t e r i o r a t i o n .
(6)
W h e n t h i s u n i t i s i n s t a l l e d i n s i d e o t h e r e q u i p m e n t , p a y a t t e n t i o n t o t h e h e a t
r a d i a t i o n a n d k e e p t h e h e a t i n s i d e t h e e q u i p m e n t 5 0
℃
o r b e l o w .
Caution
！
Caution
！
(1)
Applying a voltage or current exceeding its maximum permissible value may cause the unit to be
damaged.
(2)
(3)
(4)
(5)
For the purpose of functional improvement, the information w ritten herein may be changed w ithout
prior notice.
Alw ays use the unit w ithin the specified voltage range; otherw ise, it may cause a fire, electric
shock or personal/equipment damage.
Information contained herein is considered accurate to the best of our know ledge. If you have any
question or comment on the information, please contact us or our distributor.
Read this manual carefully and thoroughly before starting to operate the unit, and keep the
manual available for future reference.
120 mm or more
70
m
m
o
r
m
o
re
+
0
.6
-0
45
92
-0
+0.8
Instruction Manual for EDI62S Series
Digital Straingauge Meters
12/12
(ED-34824)
Unit indication label
Accessory
Quantity
6-p terminal cover
3 pieces
1 each
Mounting band
2 pieces
Suitable solderless terminals
5.8 mm or
less
5.8 mm or
less
Top
Bottom
①
+SIG (D) sensor input (+)
②
-SIG (B) sensor input (-)
③
+EXC (A) sensor supply power (+)
④
-EXC (C) sensor supply power (-)
⑤
AG (E) analog ground
⑥
NC space terminal
Display
Description
Indicates that each judgment value of comparator data or the size of
hysteresis parameters does not meet the conditions.
Indicates that a signal exceeding the measurement range has been
applied.
Indicates that an input signal once exceeded the measurement
range, but has returned to the measurable range with the peak hold
function activated.
Indicates that the unit is waiting for an A/D converter input or that
power-ON delay time is valid.
Indicates that digital limiter HI and digital limiter LO of scaling data
have the same value.
Indicates that analog output HI and analog output LO of scaling data
have the same value.
Linearize data error
Indicates that full-scale input value and off-set input value of scaling
data have the same value.
* Turning power ON with the Enter key and Mode key held down causes all the
parameters to return to the initial values (defaults).
Memory switch area, checksum error of main memory
Calibration data area, checksum error of main memory
Memory switch area, checksum error of sub-memory
Calibration data area, checksum error of sub-memory
Condition data area, checksum error
Press the Mode key for a prolonged time to load the initial values.
Scaling data area, checksum error (for each pattern)
Press the Mode key for a prolonged time to load the initial values of each
pattern.
Comparator data area, checksum error (for each pattern)
Press the Mode key for a prolonged time to load the initial values of each
pattern.
Calibration data area, checksum error (for each pattern)
Press the Mode key for a prolonged time to load the initial values of each
pattern.
Shift data area, checksum error
Press the Mode key for a prolonged time to load the initial values.
Linearize data area, checksum error
Press the Mode key for a prolonged time to load the initial values.
Display
Description
*2 + time delay +(*1×2)+500μs+*3
*2
*3
Time delay +(*1×2)+500μs+*3
*3
Internal
sampling
Specified
sampling
S/H terminal
Comparator
output update
Start/hold type A
*1
Internal
sampling
Specified
sampling
S/H terminal
Comparator
output update
Start/hold type B
*1
10
Error Message
10.1Error Indication during Measurement or Setup
10.2Memory Failure Error Indication
11
Timing Charts
12
Warranty and Service
12.1 Warranty
The warranty period of the product is one year from the date of
delivery. If a failure occurs during this period that is clearly judged to
be caused by a defect ascribable to Asahi Keiki, we will repair the
failure or replace any defective parts without charge.
12.2 After Sales Service
Under strict quality control measures, this product was manufac-
tured, tested, inspected and shipped. Should a defect in manufacture
or workmanship be identified, please return the product to our dis-
tributor or directly to us. It would be highly appreciated if you could
give a detailed account of the fault and enclose it with the product.
*1 Specified sampling
AVG
setting
1
Sampling speed
1041.65 times/sec
2
520.825 times/sec
4
8
10
104.165 times/sec
20
50
52.0825 times/sec
20.833 times/sec
AVG
setting
100
Sampling speed
10.4165 times/sec
200
5.20825 times/sec
400
2.604125 times/sec
800
1000
1.04165 times/sec
2000
5000
0.520825 times/sec
0.20833 times/sec
*2 External start signal
*3 Time delay for alarm output
Relay output: 10 ms max.
The width of the external start signal must be from between 500
μ
s to a specified sampling cycle. A time
delay can be set for the external start using the S/H delay time parameter of the condition data.
The sampling speed is determined by the AVG parameter setting of condition data as shown in the table below:
1.3020625 times/sec
260.4125 times/sec
130.20625 times/sec
Sampling cycle
Approx. 48 ms
Approx. 19.2 ms
Approx. 960 s
Approx. 1.92 ms
Approx. 3.84 ms
Approx. 7.68 ms
Approx. 9.6 ms
Sampling cycle
Approx. 4.8 sec
Approx. 1.92 sec
Approx. 96 ms
Approx. 192 ms
Approx. 384 ms
Approx. 768 ms
Approx. 960 ms
Photo coupler output: Maximum 200
μ
s
Illustration of the rear
Input unit
Comparator output unit
Analog output unit
Power supply unit
ＥＤＩ６２Ｓ
Power supply
AC:100 to 240V AC±10%
DC:12 to 48V DC±10％
－
Suitable solderless terminals
5.8 mm or
less
5.8 mm or
less
Top
Bottom
①
HI a (HI output a contact)
②
HI c (HI output COM)
③
GO a (GO output a contact)
④
GO c (GO output COM)
⑤
LO a (LO output a contact)
⑥
LO c (LO output COM)
Customer service
Bessho-chou 85-7, Saitama-shi, kita-ku
TEL +81-048-662-4911
Saitama-ken 331-0821, Japan
ENERPAC JAPAN
FAX +81-048-662-4955
WEB http://www.apj.ne.jp
