BASE FRAME
SEAT ASSEMBLY
CONSOLE
BEAM ASSEMBLY
REAR FOOT
MAST SHROUDS
PIVOT SHROUD
LEG ASSEMBLY
CONSOLE MAST
GAS SPRING
SEAT STOP
M6 x 10mm Cap Head Screw
M8 x 15mm Button Head Screw
M4 x 20mm Flat Head Phillips Screw
HARDWARE DESCRIPTION
DRAWING QUANTITY
M4.2 x 19mm Self Threading Phillips Screw
M5 x 12mm Round Head Phillips Screw
M5 x 45mm Cap Head Screw
4
4
4
5
2
1
M8 x 15mm Flat Head Screw
M8 x 35mm Cap Head Screw
M8 x 55mm Cap Head Screw
M10 x 20mm Cap Head Screw
M10 x 65mm Cap Head Screw
1
1
2
4
4
M8 Lock Nut
M8 Washer
1
2
ASSEMBLY TOOLS
5 mm
Hex Wrench
8 mm
Hex Wrench
Combo
Wrench
6 mm
Hex Wrench
4 mm
Hex Wrench
M8 Lock Nut (Black)
M8 Washer (Black)
1
2
ASSEMBLY AND
OPERATING INSTRUCTIONS
ASSEMBLY
The EnergyFit Ski-Row requires minimal assembly. All tools required to complete the initial setup and
assembly have been included in the Assembly Hardware Kit. Prior to assembly, remove the unit and all
parts from the carton and packaging. Confirm all parts shown in the section tiltled “As Shipped” above
are included before attempting to assemble the Ski-Row.
1582 Parkway Loop, Suite A Tustin, California 92780 Ph. 1-657-345-4530
For more information or questions regarding your product, please visit our website at www.energy.fit
© EnergyFit 2020
Assembly Step 1:
Install the Beam Foot Assembly to the Beam End with two M10 x 20mm Socket Head Screws using an
8mm hex wrench. Next, slide the Seat Assembly onto the front end of the beam, being sure to orient the
wide end of the seat toward the rear of the beam. Finally, install the Seat Stop to the beam with two M5
x 15mm Phillips Drive Round Head Machine Screws and a #2 Phillips Screwdriver.
Assembly Step 3:
Press down on the Beam Release Lever and move the Beam Bracket down into the horizontal position.
Place the beam on the floor behind the Base Frame and carefully slide the Beam all the way onto the
Beam Bracket, and secure it with four M8 x 15mm flat head socket screws and four M8 x 15mm Button
Head Screws using a 5mm Hex wrench.
Next, install the Beam Pivot Cover by snapping it down in place over the Beam Bracket, and secure it with
four M4 x 20mm Flathead Machine Screws and a #2 Phillips Screwdriver.
Assembly Step 4:
WARNING:
THE ORDER OF THE
FOLLOWING STEPS ARE
CRITICAL FOR SUCCESSFUL
ASSEMBLY AND OPERATION.
Raise the beam to the vertical position
untill the Beam Lock clicks into place.
Install the Ski Pulley M5 x 45mm Link
Screw with a 4mm hex wrench through
the lower hole in the access cover, then
REMOVE the M5 shoulder screw to free
the ski pulley assembly.
Assembly Step 5:
Install the gas spring by screwing the threaded
stud on the cylinder into the end fitting on the Base
Frame. Align the end fitting on the top of the gas
spring rod to the clevis on the Beam, and secure
with a M8 x 35 mm socket head cap screw, two M8
washers, and M8 lock nut using 6mm hex wrench
and multi-wrench.
AS SHIPPED
Assembly Step 6:
Uncoil and straighten out the Console Cable.
Carefully feed the cable through the Console
Support Mast and all the way out the end. Attach
the Console to the Console Support Mast with a
M8 x 55mm bolt, two Black M8 Washers, and one
Black M8 Lock Nut.
Next, attach the Console Support to the base
frame with four M6 x 10mm screws and a 5mm
Hex Wrench, being carefull not to pinch the cable
between the Console Support and the Base
Frame.
Assembly Step 2:
Install the Leg Assembly onto the Base Frame with
four M10 x 65mm Socket Head Cap Screws and a
8mm Hex wrench.
Assembly Step 7:
Connect cables together.
Next, install the two Mast Shrouds to the Base Frame
with five M4.2 x 19mm Phillips Head Screws using a #2
Phillips Screwdiver.
Finally, install four C type alkaline batteries in the back
of the console housing. Note that there are two battery
compartments and two batteries must be installed in
each compartment in the orientation specified for the
console to operate correctly.
