Endress+Hauser Turbimax CUS52D Скачать руководство пользователя страница 38

Страница: 38 / 48

Accessories

Turbimax CUS52D

Hauser

Accessories

The following are the most important accessories available at the time this documentation

was issued.

‣

For accessories not listed here, please contact your Service or Sales Center.

12.1 Assemblies

FlowFit CUA120

• Flange adapter for mounting turbidity sensors

• Product Configurator on the product page:

www.endress.com/cua120

Technical Information TI096C

Flowfit CUA252

• Flow assembly

• Product Configurator on the product page:

www.endress.com/cua252

Technical Information TI01139C

Flowfit CUA262

• Weld-in flow assembly

• Product Configurator on the product page:

www.endress.com/cua262

Technical Information TI01152C

Flexdip CYA112

• Immersion assembly for water and wastewater

• Modular assembly system for sensors in open basins, channels and tanks

• Material: PVC or stainless steel

• Product Configurator on the product page:

www.endress.com/cya112

Technical Information TI00432C

Cleanfit CUA451

• Manual retractable assembly made of stainless steel with ball valve shut-off for turbidity

sensors

• Product Configurator on the product page:

www.endress.com/cua451

Technical Information TI00369C

Flowfit CYA251

• Connection: See product structure

• Material: PVC-U

• Product Configurator on the product page:

www.endress.com/cya251

Technical Information TI00495C

Flowfit CUA250

• Flow assembly for water and wastewater applications

• Product Configurator on the product page:

www.endress.com/cua250

Technical Information TI00096C

Built-in adapter

• For installing CUS52D in CUA250 or CYA251 assembly

• Order number: 71248647

Содержание Turbimax CUS52D

















































Результаты поиска

Содержание Turbimax CUS52D

Отзывы:

Похожие инструкции для Turbimax CUS52D

Бренды по названию

Популярные бренды

Endress+Hauser Turbimax CUS52D, Руководство по эксплуатации

Результаты поиска

Содержание Turbimax CUS52D

Отзывы:

Похожие инструкции для Turbimax CUS52D

Бренды по названию

Популярные бренды