Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 57

Страница: 57 / 114

Operating the Analyzer

Operator’s Manual

–

•

Laser Zero Low Alarm

: This fault occurs if the detector signal value

is below the set normal range when the laser is turned off.

•

PeakTk Restart Alarm

: This fault occurs when the number of

consecutive system restarts caused by a peak tracking correction

exceeds a preset limit.

•

Pressure High Alarm

: This fault occurs when the pressure in the

sample cell exceeds the specified maximum operating pressure.

•

Pressure Low Alarm

: This fault occurs when the pressure in the

sample cell is below the specified minimum operating pressure.

•

Temp High Alarm

: This fault occurs when the temperature in the

measurement cell exceeds the specified maximum operating

temperature.

•

Temp Low Alarm

: This fault occurs when the temperature in the

measurement cell is below the specified minimum operating

temperature.

•

Validation 1 Failed/Validation 2 Failed Alarm

: An additional

alarm for systems equipped with autovalidation that is triggered

when the measured concentration of the validation 1 or 2 gas does

not agree with the user defined allowable limits. These alarms also

trigger the Validation Fail dry contact relay. Refer to

“Validation

Allowance”

on page 2-33. Once activated, the

Validation Fail

Alarm

must be manually reset via the Cancel Val Alarms parameter

(see

“Cancel Val Alarms”

on page 2-19).

Refer to Appendix A

for recommendations and solutions to common problems

resulting in a system fault.

User alarms

User alarms are generated based on measurement readings and their relation

Mode 2

parameter settings. They include the following:

•

Concentra High Alarm

: This fault occurs when the measured

concentration is above the limit set with the

High Alarm Setpoint

parameter (see

“High Alarm Setpoint”

on page 2-24).

•

Concentra Low Alarm

: This fault occurs when the measured

concentration is below the set limit with the

Low Alarm Setpoint

(see

“Low Alarm Setpoint”

on page 2-25).

For systems with heated enclosures, a

Temp Low Alarm

Temp High Alarm

fault will activate the

General Fault Alarm

when the enclosure temperature is more than 5



C above or below

the specified temperature (refer to the system drawings or

calibration report for this analyzer). Once the enclosure has

reached the specified temperature, reset the

General Fault

Alarm

(see

“To change parameters in Mode 2”

on page 2-15).

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды