Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 38

Страница: 38 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

General Alarm DO

The

General Alarm DO

sets the operation of the general alarm relay digital

output when a general fault alarm occurs. The relay is normally energized

making it fail-safe for detection of not only alarms, but also power failures.

Enter

to make the relay latching, which means any general fault alarm will

de-energize the relay and keep it de-energized even if the alarm condition

clears. This parameter must be reset to return the relay to ‘normal’ state. Enter

to make the relay non-latching, which means any general fault alarm will

de-energize the relay; however, when the alarm condition clears, the relay will

automatically reset to its normal state. Enter a

to reset the relay and any

active alarms to the ‘normal’ state. After the relay resets, this parameter will

automatically revert to the setting from before the reset was initiated.

High Alarm Setpoint

The

High Alarm Setpoint

parameter determines the concentration threshold

above which the

Concentra High Alarm

fault will be triggered (refer to

“Alarms”

on page 2-42). The value entered is compared to the moving

average over the number of measurement points set by the

Logger Rate

. The

setpoint must have a value greater than the maximum range of the analyzer

or maximum dew point to be turned off.

Keypad Watchdog

The

Keypad Watchdog

parameter sets the allowable time (in seconds) that

the analyzer can be on the MODE screen and the

Mode 2

(Set Parameter

Mode) password screen before automatically reverting to

Mode 1

(Normal

Mode). Setting this parameter to a value less than five (5) will disable this

feature. If it is set for greater than or equal to five (5), then the value

represents the number of seconds before the analyzer reverts to Normal Mode.

General Alarm DO

0:L 1:NonL 2:Reset

High Alarm Setpoint

0.00000

ppmv or DewPoint F/C

Keypad Watchdog

<5:Off >=5:Secs

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды