Endress+Hauser Prosonic M FMU42 Скачать руководство пользователя страница 39

Страница: 39 / 52

Prosonic M FMU42 HART

Maintenance

Hauser

Selection

• Delete: delete (reset) an existing interference echo suppression

• Inactive: switch off interference echo suppression, mapping is saved

• Active: switch interference echo suppression back on

10.7 Firmware history

V01.02.00 (01.2002) / V01.02.02 (03.2003)

• Valid from documentation version: BA237F/00/en/03.03

• Software changes:

Original software

• Compatible with:

• ToF Tool

• Commuwin II (from version 2.05.03)

• HART Communicator DXR 275 (from OS 4.6) with Rev. 1, DD 1

V01.02.04 (02.2004)

• Valid from documentation version: BA237F/00/en/02.04

FMU42 added

• Software changes:

FMU42 added

• Compatible with:

HART Communicator DXR 375

V01.04.00 (07.2006)

• Valid from documentation version: BA237F/00/en/07.06

"Detection window" added. Version :07.06

• Software changes:

"Detection window" function added

• Compatible with:

• ToF Tool from version 4.50

• HART Communicator DXR375 with Rev. 1, DD 1

Maintenance

11.1 Maintenance schedule

As a general rule, no specific maintenance work is required.

11.2 Maintenance tasks

11.2.1 Cleaning

When cleaning the exterior, always use cleaning agents that do not corrode the surface of

the housing and the seals.

Содержание Prosonic M FMU42





















































Результаты поиска

Содержание Prosonic M FMU42

Отзывы:

Похожие инструкции для Prosonic M FMU42

Бренды по названию

Популярные бренды

Endress+Hauser Prosonic M FMU42, Руководство по эксплуатации

Результаты поиска

Содержание Prosonic M FMU42

Отзывы:

Похожие инструкции для Prosonic M FMU42

Бренды по названию

Популярные бренды