Endress+Hauser Proline Promass O 300 Скачать руководство пользователя страница 86

Страница: 86 / 96

Proline Promass O 300

Hauser

Certification PROFIBUS

PROFIBUS interface

The measuring device is certified and registered by the PNO (PROFIBUS User Organization

Organization). The measuring system meets all the requirements of the following specifications:

• Certified in accordance with PROFIBUS PA Profile 3.02

• The device can also be operated with certified devices of other manufacturers (interoperability)

EtherNet/IP certification

The measuring device is certified and registered by the ODVA (Open Device Vendor Association).

The measuring system meets all the requirements of the following specifications:

• Certified in accordance with the ODVA Conformance Test

• EtherNet/IP Performance Test

• EtherNet/IP PlugFest compliance

• The device can also be operated with certified devices of other manufacturers (interoperability)

Certification PROFINET

PROFINET interface

The measuring device is certified and registered by the PNO (PROFIBUS User Organization

Organization). The measuring system meets all the requirements of the following specifications:

• Certified according to:

– Test specification for PROFINET devices

– PROFINET Security Level 2 – Netload Class

• The device can also be operated with certified devices of other manufacturers (interoperability)

Pressure Equipment

Directive

The devices can be ordered with or without a PED approval. If a device with a PED approval is

required, this must be explicitly stated in the order.
• With the identification PED/G1/x (x = category) on the sensor nameplate, Hauser

confirms conformity with the "Essential Safety Requirements" specified in Appendix I of the

Pressure Equipment Directive 2014/68/EU.

• Devices bearing this marking (PED) are suitable for the following types of medium:

– Media in Group 1 and 2 with a vapor pressure greater than, or smaller and equal

to0.5 bar (7.3 psi)

– Unstable gases

• Devices not bearing this marking (PED) are designed and manufactured according to good

engineering practice. They meet the requirements of Article 4 paragraph 3 of the Pressure

Equipment Directive 2014/68/EU. The range of application is indicated in tables 6 to 9 in Annex II

of the Pressure Equipment Directive 2014/68/EU.

Radio approval

The measuring device has radio approval.

For detailed information on the radio approval, see the Special Documentation →  93

Measuring instrument

approval

The measuring device is (optionally) approved as a gas meter (MI

‐

002) or component in measuring

systems (MI-005) in service subject to legal metrological control in accordance with the European

Measuring Instruments Directive 2004/22/EC (MID).
The measuring device is qualified to OIML R117 or OIML R137 OIML R117 and has an OIML

Certificate of Conformity (optional).

Additional certification

CRN approval

Some device versions have CRN approval. A CRN-approved process connection with a CSA approval

must be ordered for a CRN-approved device.

Tests and certificates

• Pressure test, internal procedure, inspection certificate

• EN10204-3.1 material certificate, wetted parts and sensor housing

• PMI test (XRF), internal procedure, wetted parts, test report

• EN10204-2.1 confirmation of compliance with the order and EN10204-2.2 test report

Содержание Proline Promass O 300

































































































Результаты поиска

Содержание Proline Promass O 300

Отзывы:

Похожие инструкции для Proline Promass O 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promass O 300, Техническая информация

Результаты поиска

Содержание Proline Promass O 300

Отзывы:

Похожие инструкции для Proline Promass O 300

Бренды по названию

Популярные бренды