Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 44

Страница: 44 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

Hauser

Additional information

Description

Displays all the options that are available if ordered by the customer.

"Extend. HistoROM" option

Order code for "Application package", option

"Extended HistoROM"

"ECC" option

Order code for "Application package", option

"ECC electrode cleaning"

"HBT Verification" option and "HBT Monitoring" option

Order code for "Application package", option

"Heartbeat Verifi Monitoring"

"Custody transfer" option

The measuring device has an approval for custody transfer measurement.

Detailed information on the national and international approvals for custody transfer

that are currently available can be supplied by your Hauser sales

organization.

3.2

"Sensor" submenu

Navigation

 Expert → Sensor

‣

Sensor

‣

Measured val.

→  44

‣

System units

→  55

‣

Process param.

→  70

‣

External comp.

→  83

‣

Sensor adjustm.

→  88

‣

Calibration

→  95

3.2.1

"Measured val." submenu

Navigation

 Expert → Sensor → Measured val.

‣

Measured val.

‣

Process variab.

→  45

‣

Totalizer

→  48

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды