Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 131

Страница: 131 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

131

Additional information

Selection

• Actual value

In the event of a device alarm, the frequency output continues on the basis of the current

flow measurement. The device alarm is ignored.

• Defined value

In the event of a device alarm, the frequency output continues on the basis of a

predefined value. The Failure freq. (→  131) replaces the current measured value,

making it possible to bypass the device alarm. The actual measurement is switched off

for the duration of the device alarm.

• 0 Hz

In the event of a device alarm, the frequency output is "switched off".

NOTICE!

A device alarm is a measuring device error that must be taken seriously. It can

affect the measurement quality such that the quality can no longer be guaranteed. The

Actual value

option is only recommended if it can be guaranteed that all possible alarm

conditions will not affect the measurement quality.

Failure freq.



Navigation

 Expert → Output → PFS output 1 to n → Failure freq. (0474–1 to n)

Prerequisite

One of the following options is selected in the

Assign curr.

parameter (→  106):

• Volume flow

• Mass flow

• Correct.vol.flow

• Flow velocity

• Conductivity

• CorrConductivity

• Temperature

• Electronic temp.

Description

Use this function to enter the value for the frequency output in the event of a device alarm

in order to bypass the alarm.

User entry

0.0 to 12

500.0 Hz

Factory setting

0.0 Hz

Output freq. 1 to n

Navigation

 Expert → Output → PFS output 1 to n → Output freq. 1 to n (0471–1 to n)

Prerequisite

In the

Operating mode

parameter (→  120), the

Frequency

option is selected.

Description

Displays the actual value of the output frequency which is currently measured.

User interface

0.0 to 12

500.0 Hz

Visibility depends on order options or device settings

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды