Endress+Hauser Micropilot S FMR530 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 92

background image

Accessories

Micropilot S FMR533 4 to 20 mA HART

68

Hauser

8

Accessories

A variety of accessories is available for the Micropilot S. They can be ordered separately from
Hauser.

8.1

Weather protection cover

A weather protective cover made of stainless steel is available for outdoor mounting
(order code: 543199-0001). The shipment includes the protective cover and tension clamp.

L00-FMR53xxx-00-00-06-en-001

8.2

Commubox FXA195 HART

For intrinsically safe communication with FieldCare via the USB interface.
For details refer to TI00404F/00/EN.

8.3

Commubox FXA291

The Commubox FXA291 connects Hauser field devices with CDI interface
(= Hauser Common Data Interface) to the USB interface of a personal computer or a
notebook. For details refer to TI00405C/07/EN.

!

Note!
For the device you need the "ToF Adapter FXA291" as an additional accessory.

8.4

ToF Adapter FXA291

The ToF Adapter FXA291 connects the Commubox FXA291 via the USB interface of a personal
computer or a notebook to the device. For details refer to KA00271F/00/A2.

«
...
66
67
68
69
70
...
»

Содержание Micropilot S FMR530





























































































Отзывы:

Нет отзывов

Похожие инструкции для Micropilot S FMR530

Бренд: Oakton Страницы: 4

Бренд: Jasco Страницы: 48

Бренд: Vaisala Страницы: 90

Бренд: Vaisala Страницы: 4

Signet FlowtraMag 2580 Series

Бренд: GF Страницы: 20

Бренд: Ocea Soft Страницы: 19

Бренд: Magene Страницы: 80

Бренд: Datakom Страницы: 2

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренд: Roland Страницы: 2

Бренд: Kawai Страницы: 2

EUROGRAND EG2080

Бренд: Behringer Страницы: 34

Бренд: Hanna Instruments Страницы: 12

Бренд: D-tect Systems Страницы: 2

Бренд: GasQuip Страницы: 8

NEO MP18X Series

Бренд: MA Страницы: 3

Бренд: Digitimer Страницы: 58

Бренд: Eplus Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды