Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 94

Страница: 94 / 100

Operation via FOUNDATION Fieldbus

iTEMP TMT85

Hauser

A0042931

Select one of these bits (here for example: Configurable Area Bit 1) and select the

Drift option from the corresponding selection list. Press Enter to confirm the option

selected.

A0042932

Now go to the Resource Block and activate the corresponding bit (here: Configurable

Area Bit 1) in the FD_OFFSPEC_MAP parameter.

4. The measurement value status can now also be set for this event. With the

STATUS_SELECT_103 parameter, the measured value status BAD is selected for this

purpose via the selection menu.

14.7.4 Reasons for a diagnostic event and corrective action

In the FD_RECOMMEN_ACT parameter in the Resource Block, a description is displayed

for the diagnostic event with the highest priority that is currently active. This description

has the following structure:
Diagnostic number:Diagnostic text with channel (ch x):troubleshooting recommendations

separated by hyphens, e.g. for the diagnostic event sensor break: 41:Sensor break

ch01:Check electrical connection - Replace sensor - Check configuration of the connection

type
The value transmitted via the bus has the following structure: XXYYY
XX = Channel number
YYY = Diagnostic number
For the "Sensor break" example above, this value is 01041

14.8 Transmission of event messages over the bus

The process control system used must support the transmission of event messages.

Содержание iTEMP TMT85





































































































Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды

Endress+Hauser iTEMP TMT85, Руководство по эксплуатации

Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды