Endress+Hauser Deltabar FMD72 Скачать руководство пользователя страница 89

Страница: 89 / 108

Deltabar FMD72

Description of device parameters

Set Min. Current (053)

Navigation

Setup

Advanced Setup

Current Output

Set Min. Current (053)

Write permission

Operators/Service engineers/Expert

Description

Enter lower current limit.
Some switching units accept no current smaller than 4.0 mA.

Options

• 3.8 mA
• 4.0 mA

Factory setting

3.8 mA

Output current (054)

Navigation

Setup

Advanced Setup

Current Output

Output Current (054)

Write permission

Operators/Service engineers/Expert

Description

Displays the current current value.

ALARM STATUS (071)

Navigation

Diagnosis

Diagnostic Code (071)

Write permission

No write permissions. Parameter is read only.

Description

Displays the diagnostic message with the highest priority currently present.

Last diag. code (072)

Navigation

Diagnosis

Last Diag. Code (072)

Write permission

No write permissions. Parameter is read only.

Description

Displays the last diagnostic message that occurred and was rectified.

Note

• Digital communication: the last message is displayed.
• Use the "Reset logbook" parameter to clear the messages listed in the parameter "Last diag. code".

Содержание Deltabar FMD72













































































































Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar FMD72, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды