ENCAD 42e Скачать руководство пользователя страница 127

Страница: 127 / 162

Assembly\Disassembly

127

ASSEMBL

DISASSEMBL

Novajet PROe Series Service Manual

Push both sides of the connector lock shut at the same

time.

To install the Encoder Sensor:

Turn the Carrier Assembly so that the bottom side of it is

facing up.

Push down on the plastic clip and slide the back of the

Encoder Sensor over it.

Push the Encoder Sensor in past the ridges until the

Encoder Sensor snaps into place.

d. Turn the Carrier Assembly over and insert the Encoder
flex cable into the connector at J2.

Push both sides of the connector lock shut at the same

time.

Perform the Carrier Assembly, Carrier Belt, and the Frame
Tensioner Reinstallation procedures to reinstall the Carrier
Assembly.

Replacing the Carrier Bushings

If there is not enough space on both sides of the Slide Shaft to
remove the Carrier bushings, perform the Carrier Assembly,
Carrier Belt, and the Frame Tensioner Removal procedures
to remove the Carrier Assembly from the Slide Shaft.

Содержание 42e



































































































































































Результаты поиска

Содержание 42e

Отзывы:

Похожие инструкции для 42e

Бренды по названию

Популярные бренды

ENCAD 42e, Руководство по обслуживанию

Результаты поиска

Содержание 42e

Отзывы:

Похожие инструкции для 42e

Бренды по названию

Популярные бренды