EN-KO Electronics AMF 4.0 Скачать руководство пользователя

Страница: 21 / 22

EN-KO Electronic Control Systems

AMF 4.0/ENG/K.K./02

SPECIFICATIONS

Power Supply

9-35 VDC
140 mA (all relays are de-energized)

Ambient
Temperature

-10

C / +70

Relative Humidity

%10-%95 non-condensing

Relay outputs

For cranking, fuel solenoid, preheating and auxiliary outputs max.
12V/24VDC 6 A, For mains and generator contactor relays max.
250VAC/10 A

Voltage measurement

20-300VAC

Frequency
measurement

1-99 Hz

Current
measurements

.../5 A current inputs (current transformer should be used)

Connection

Screw socket

Measurement
Accuracy

Phase voltages

: + / - %2

Frequency

: + / - 0.1Hz

Phase currents

: + / - %2

Charge Excitation
Current

80mA @ 12VDC
160mA@ 24VDC

Housing

PPO (Polyphenylene oxide) %30 Glass Fiber

Protection Class

IP 52 (Front side)

Weight

600 gr. (aprox.)

Dimensions (WxHxD)

192x144x62 mm

Panel Cut Out

186x138 mm

Mounting Installation

Front panel mounted with metal screw fixings

DIMENSIONS AND MOUTING

Содержание AMF 4.0























Результаты поиска

Содержание AMF 4.0

Отзывы:

Похожие инструкции для AMF 4.0

Бренды по названию

Популярные бренды

EN-KO Electronics AMF 4.0, Руководство пользователя

Результаты поиска

Содержание AMF 4.0

Отзывы:

Похожие инструкции для AMF 4.0

Бренды по названию

Популярные бренды