background image

 
WEL-

200™ Operating Instructions 

 

16 

Document no.

  10320104                                            Revision 2.0 

3-1-18

 

 

Ordering Information 

 

WEL-200K 

Wireless edge link kit, 1 transmitter and 1 receiver 

WEL-200T 

Wireless edge link transmitter 

WEL-200R 

Wireless edge link receiver 

 

Warranty 

 
 

 

 
 

 

 

 

 
 
 

  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

EMX Industries Incorporated warrants all products to be free of defects in 
materials and workmanship for a period of two years under normal use and 
service from the date of sale to our customer.  This warranty does not cover 
normal wear and tear, abuse, misuse, overloading, altered products, damage 
caused by incorrect connections, lightning damage, or use other than intended 
design. 

There is no warranty of merchantability.  There are no warranties expressed or 
implied or any affirmation of fact or representation except as set forth herein. 

EMX Industries Inc. sole responsibility and liability, and the purchaser’s 
exclusive remedy shall be limited to the repair or replacement at EMX 
Industries option of a part or parts found not conforming to the warranty.  In 
no event shall EMX Industries Inc. be liable for damages, including but not 
limited to damages resulting from non-conformity, defect in material or 
workmanship. 

 

Effective date:  January 1

st

, 2002 

 

Содержание WEL-200 Series





















Отзывы: