Emulex LPe16000B-series HBA Скачать руководство пользователя страница 6

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual

P008875-02A Rev. A

1. Introduction

Overview

6

1. Introduction

Overview

This manual describes the following Fibre Channel (FC) to Peripheral Component 
Interconnect Express (PCIe) Emulex

® 

host bus adapters (HBAs):

LPe15004, 8 gigabit per second (Gb/s)

LPe16000B, LPe16002B, and LPe16004, 16 Gb/s

The core technology of these HBAs is Emulex's 10th generation FC controller. The 

controller is a multi-function PCIe Gen3 interface controller that is compliant to the PCI 

Express Base Specification Rev 3.0 and PCI Express CEM Specification Rev 3.0. The 

LPe16000B is a single-channel adapter, the

 

LPe16002B is a dual-channel adapter, and 

the LPe15004 and LPe16004 are four-channel adapters.
These HBAs support packet transfers at 2.5, 5.0, and 8 gigatransfers per second (2.5, 5.0, 

and 8 GT/s) on the PCIe link (auto-negotiated with the system). The supported 

physical PCIe connector is x8. The fully featured FC port is compliant to various 

American National Standards Institute (ANSI) FC standards.

Note:

Illustrations in this manual are only examples. The actual hardware may vary.

Major Features

Multi-function PCIe 3.0 device with one (LPe16000B), two (LPe16002B), or four 

(LPe15004 and LPe16004) independent FC ports.

Auto-negotiation between 4-Gb/s, 8-Gb/s, or 16-Gb/s (LPe16000B, LPe16002B, 

and LPe16004 adapters only) FC link speeds.

Complies with the PCIe base and CEM 3.0 specifications.

x8-lane standard Generation 3, PCIe interface at 2.5GT/s, 5GT/s, or 8GT/s 

(auto-negotiated with the system).

ECC protection of high density RAM (single-bit correction, double-bit 

detection).

SFP+ interface supporting optics with LC connections and digital diagnostics 

capability.

Host interface support is provided through Emulex standard drivers. 

The LPe15004 adapter supports Windows Server 2012, Windows Server 

2008, Windows Hyper-V, Citrix, Kernel-based Virtual Machine (KVM), 

VMware ESXi, Red Hat Enterprise Linux (RHEL), SUSE Linux Enterprise 

Server (SLES), Oracle Enterprise Linux (OEL), and Solaris S11 (x86 and 

Solaris Sparc)

The LPe16000B-series adapters supports Windows Server 2008 R2 and WS 8, 

Red Hat Enterprise Linux, VMware ESXi, and Solaris S11 (including 

Comstar).

Содержание LPe16000B-series HBA





















Отзывы: