EMTAC CRUX II/BTGPS Скачать руководство пользователя страница 2

 

1

Federal Communication Commission Interference Statement 

 
This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules.    These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation.  This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications.  However, there is no guarantee 
that interference will not occur in a particular installation.    If this equipment does 
cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one of the following measures: 
-Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

FCC Caution: To assure continued compliance, (example - use only shielded 
interface cables when connecting to computer or peripheral devices). Any changes 
or modifications not expressly approved by the party responsible for compliance 
could void the user's authority to operate this equipment. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation. 

 
IMPORTANT NOTE: 
FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated with 
minimum distance 20cm between the radiator & your body. 
This transmitter must not be co-located or operating in conjunction with any other 
antenna or transmitter. 

 

Содержание CRUX II/BTGPS












Отзывы: