background image

31629-13-1215

Page 3

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

•  Due to high temperatures the appliance should be 

located out of traffic and away from furniture and 

draperies.

•  The glass front or any part removed for servicing 

the appliance must be replaced prior to operating 

the appliance. Work should be done by a qualified 

service person.

•  Keep burner and control compartment clean. 
•  Vent cap is hot while fireplace is in operation.
•  Installation and repair should be done by a 

QUALIFIED SERVICE PERSON. The appliance 

should be inspected before use and at least annually 

by a qualified service person. More frequent 

cleaning may be required due to excessive lint from 

carpeting, bedding materials, etc. It is imperative 

that control compartments, burners and circulating 

air passageways of the appliance be kept clean.

•  DO NOT put anything around the fireplace that will 

obstruct the flow of ventilation air.

•  Clearance in accordance with local installation codes 

and the requirements of the gas supplier.

• DO keep the appliance area clear and free from 

combustible material, gasoline and other flammable 

vapors and liquids.

• DO examine venting system periodically and replace 

damaged parts.

• DO 

make a periodic visual check of pilot and burners. 

Clean and replace damaged parts.

•  CAUTION:  The  glass  used  in  your  fireplace  is 

tempered glass. If the glass is cracked or damaged in 

any way, it should be replaced only with a complete 

glass frame assembly from Empire. See parts list 

on Pages

 

56 - 63 for ordering.

•  DO NOT use this fireplace if any part has been under 

water. Immediately call a qualified service technician 

to inspect the heater and to replace any part of the 

control system and any gas control which has been 

under water.

•  Any safety screen or guard removed for servicing 

an appliance must be replaced prior to operating 

the appliance.

•  If this appliance is installed directly on carpeting, 

tile or other combustible material other than wood 

flooring the appliance shall be installed on a metal 

or wood panel extending the full width and depth 

of the appliance. 

  The base referred to above does not mean the 

fireproof base as used on wood stoves. The 

protection is for rugs that are extremely thick and 

light colored tile.

•  Children and adults should be alerted to the hazards 

of high surface temperatures and should stay away 

to avoid burns or clothing ignition.

•  Young children should be carefully supervised when 

they are in the same room as the appliance.

•  Clothing or other flammable material should not be 

placed on or near the appliance.

•  Adequate accessibility clearances for servicing and 

proper operation.

•  This appliance must not share or be connected to a 

flue serving a separate solid-fuel burning appliance.

•  Keep the area around your appliance clear of 

combustible materials, gasoline and other flammable 

vapor and liquids. 

•  Under no circumstances should any solid fuels 

(wood, coal, paper or cardboard etc.) be used in 

this appliance.

•  The flow of combustion and ventilation air must not 

be obstructed in any way.

•  Young children should be carefully supervised 

when they are in the same room as the appliance. 

Toddlers, young children, and others may be sus-

ceptible to accidental contact burns. A physical 

barrier is recommended if there are at-risk individ-

uals in the house. To restrict access to a fireplace 

or stove, install an adjustable safety gate to keep 

toddlers young children, and other at-risk individ-

uals out of the room and away from hot surfaces.

•  A barrier designed to reduce the risk of burns from 

the hot viewing glass is provided with this appli-

ance and shall be installed for the protection of 

children and other at-risk individuals. Barrier re-

quired, may be sold separately.

•  If the barrier becomes damaged, the barrier shall 

be replaced with the manufacturer’s barrier for 

this appliance.

•  Any safety screen, guard, or barrier removed for 

servicing an appliance must be replaced prior to 

operating the appliance.

IMPORTANT SAFETY INFORMATION

Содержание DVD32FP30N-2









































































Отзывы: