background image

12434-7-0706

Page 3

•  Due to high temperatures the appliance should be located 

out of traffic and away from furniture and draperies.

•  Children and adults should be alerted to the hazards of 

high surface temperatures and should stay away to avoid 

burns or clothing ignition.

•  Young children should be carefully supervised when they 

are in the same room as the appliance.

•  Clothing or other flammable material should not be placed 

on or near the appliance.

•  Any safety screen or guard removed for servicing an appli-

ance must be replaced prior to operating the appliance.

•  Keep burner and control compartment clean.  
•  Vent cap hot while furnace is in operation.
•  Installation and repair should be done by a QUALIFIED 

SERVICE PERSON.   The appliance should be inspected 

before use and at least  annually  by  a qualified service 

person.  More frequent cleaning may be required due  to 

excessive lint from carpeting, bedding materials, etc.  It 

is imperative that control compartments, burners  and 

circulating  air  passageways  of  the  appliance  be  kept 

clean.

•  DO NOT put anything around the furnace that will ob-

struct the flow of combustion and ventilation air.

•  DO keep the appliance area clear and free from combus-

tible material, gasoline and other flammable vapors and 

liquids.

•  DO  examine  venting  system  periodically  and  replace 

damaged parts.

•  DO make a periodic visual check of pilot and burner. 

Clean and replace damaged parts.

•  CAUTION: Pilot hole cover must be kept tightly closed 

during operation.

•  DO NOT use this heater if any part has been under water.  

Immediately call a qualified service technician to inspect 

the heater and to replace any part of the control system 

and any gas control which has been under water. 

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

IMPORTANT SAFETY INFORMATION

Содержание DV-25-2SG





















Отзывы: