manualshive.com logo in svg

Empire Comfort Systems DVP36FP3 series, Руководство пользователя, Страница: 17 / 76

Поделиться
Скачать
Empire Comfort Systems DVP36FP3 series Скачать руководство пользователя страница 17

26930-5-1010

Page 17

Figure 23

Examples of possible venting systems using two (2) 90° elbows. 

V is listed as minimum vertical dimensions and H1 + H2 is listed 

as total of maximum horizontal dimensions. The maximum vertical 

and horizontal distances for two (2) 90° elbows as shown in Figure 

24 is 20 feet.

Attention: Refer to Figure 21 for additional venting requirements.

Figure 24

Below Grade Installation

When it is not possible to meet the required vent terminal clearances 

of 12" (305mm) above grade level, a snorkel kit is recommended. 

It allows installation depth down to 7" (178mm) below grade level. 

The 7" (178mm) is measured from the center of the horizontal vent 

pipe as it penetrates through the wall.

Ensure the sidewall venting clearances are observed. If venting 

system is installed below ground, we recommend a window well 

with  adequate  and  proper  drainage  to  be  installed  around  the 

termination area.

TYPICAL BASEMENT INSTALLATION

Figure 22

Examples of possible venting systems using one (1) 90° elbow. 

Eight (8) feet is listed as minimum vertical vent run with 20 feet of 

maximum horizontal vent run. Vertical dimensions are based on 

centerline to centerline of pipe. Horizontal dimensions are based 

on centerline of pipe to end of termination.

Firestop at

Ceiling Level

Firestop at

Ceiling Level

vENTING FIREpLACE - TOp (continued)

Lp and Nat models

Lp and Nat models

Lp and Nat models

Содержание DVP36FP3 series













































































Отзывы:

Нет отзывов