Empire Comfort Systems DVP36FP3 series Скачать руководство пользователя

Страница: 1 / 76

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

WARNING: If not installed, operated and maintained

in accordance with the manufacturer’s instructions,

this product could expose you to substances in fuel

or from fuel combustion which can cause death or

serious illness.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA only)

or mobile home, where not prohibited by state or local

codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certified

kit is used.

Direct Vent Zero Clearance Gas

Fireplace Heater

GAS-FIRED

Installer:

Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas sup

plier.

WARNING: If the information in these instructions

are not followed exactly, a fire or explosion may

result causing property damage, personal injury

or loss of life.

WARNING

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

EMPIRE

Comfort Systems

DIRECT vENT

GAS FIREpLACE HEATER

MODEL SERIES

MILLIvOLT STANDING pILOT

Dvp36Fp3(0,1,2,3)(N,p)-5

DIRECT IGNITION

Dvp36Fp5(0,1,2,3)N-1

INTERMITTENT pILOT

Dvp36Fp7(0,1,2,3)(N,p)-5

REMOTE RF MODELS

Dvp36Fp9(1,3)(N,p)-5

UL FILE NO. MH30033

Page 1

Содержание DVP36FP3 series













































































Результаты поиска

Содержание DVP36FP3 series

Отзывы:

Похожие инструкции для DVP36FP3 series

Бренды по названию

Популярные бренды

Empire Comfort Systems DVP36FP3 series, Руководство пользователя

Результаты поиска

Содержание DVP36FP3 series

Отзывы:

Похожие инструкции для DVP36FP3 series

Бренды по названию

Популярные бренды