background image

26127-5-0111

Page 22

Before  operating  this  heater,  please  review  the  safety  warnings 

pages at the beginning of this manual and those precautions and 

warnings listed below.

1.  Know  what  type  of  ignition  system  this  model  has  (standing 

pilot)  and  follow  the  applicable  SAFETY  and  LIGHTING 

instructions.

2.  Check  to  ensure  there  are  no  gas  leaks.  If  you  are  unsure, 

turn gas off to the heater and call a service person or your gas 

utility.

CAUTION:

 Clothing or other flammable material should not be 

placed on or near the appliance.

WARNINg:  Children  and  adults  should  be  alerted  to  the 

hazard of high surface temperature and should stay away 

to avoid burns or clothing ignition. Young children should 

be carefully supervised when they are in the same room 

as the appliance.

3.  Tampering  is  DANGEROUS  and  voids  all  warranties.  Any 

component that is found to be faulty, must be replaced with an 

approved component.

Initial Lighting 

Upon completing the gas line or turning the gas valve "ON" after it 

has been in the "OFF" position, a small amount of air will be in the 

lines. When first lighting the appliance, it will take a few minutes 

for the lines to purge themselves of this air. Once the purging is 

complete, the appliance will light and operate satisfactorily.

Subsequent lightings of the appliance will not require such purging 

if the gas valve is not turned to "OFF."

Standing Pilot Operation

1.  Follow the SAFETY and LIGHTING INSTRUCTIONS for standing 

pilot controls found in this manual and on labels found attached 

to the appliance.

CAUTION: During the initial purging and subsequent lightings, 

never allow the gas valve control knob to remain depressed in 

the "pilot" position without pushing the piezo ignitor button at 

least once every second. 

2.  During the heating season, leave the control valve knob in the 

"ON" position. This will allow the pilot flame to remain lit. Turn 

the burner flame on or off with the appliance REMOTE/OFF/ON 

rocker switch, wall switch, remote control kits or 750 millivolt wall 

thermostat.

NOTE: 

The gas control valve allows you to increase or decrease the 

height of the main burner flame. The control valve has a pressure 

regulator  with  a  knob  as  shown  in  Figure  29.  Rotate  the  knob 

clockwise to "HI" to increase the flame height and counterclockwise 

to "LO" to decrease the flame height.
3.  When the heating season is over, turn the REMOTE/OFF/ON 

switch to "OFF" and the control valve to "OFF". The system, 

including the pilot light, will be shut down.

Figure 29

Maximum and Minimum Input

The gas valve on the appliance allows the input to adjust between 

a maximum input of 32,000 BTUh for natural gas and 30,000 BTUh 

for LP gas to a minimum input of 22,400 BTUh for natural gas and 

22,000 BTUh for LP gas. Consumer be advised, the maximum input 

provides the greatest amount of yellow flame and ember glow on 

the log set. The minimum input substantially decreases the yellow 

flame and ember glow on the log set.

OPERATINg gUIDELINES

Содержание DVP30CA30BN-2









































Отзывы: