R-3450
Page 5
Assembly of Cast Iron (Outer Casing) Stove Casting
(Figures 5, 6, 7, 8 and 9)
Attention: Included in the hardware package are (8) 1/4" inside diam-
eter washers. A 1/4" washer may be used with a 1/4-20 x 3/8" bolt when
assembling the stove casting parts. If a bolt hole is not tapped deep
enough for a tight fit between stove casting parts, the 1/4" washer can
be used as a shim to provide a tight fit.
The 1/4" washers are not required for assembly of the stove casting if all
the bolt holes are tapped to a proper depth.
Additonal 1/4" washers are to be purchased locally.
1. Place porcelain casting pieces on a non-abrasive surface in order
to protect the porcelain finish. The exterior of the porcelain
casting pieces should be facing the non-abrasive surface.
2. The assembly of the casting is accomplished in 6 stages:
A. Attaching legs to the sides (Figure 5).
B. Attaching rear cover to sides (Figure 6).
C. Removing protective packaging from casing front and window
(Figure 7).
D. Assembly of front by attaching retaining tabs and placing front
on unit (Figure 8).
E. Inserting firebox into partially completed assembly (Figure 9).
F. Placing top on unit.
3. Refer to Figure 5, the leg pads will have the letter "A" and "B"
stamped into the metal. Place leg pad "A" and leg pad "B" at the
bottom of each casing side. Leg pad "A" attaches to the front of the
casing side, right and to the rear of the casing side, left. Leg pad "B"
attaches to the rear of the casing side, right and to the front of the
casing side, left. Position the 3/4" flange on the leg pad against the
(2) locator dimples on the casing side. The 3/4" flange must be facing
upward, toward the top louver openings on the casing side. Attach
the two rear leg pads to the casing sides with (2) 3/8" bolts. Attach
but do not completely tighten the two front leg pads to the casing
sides with (2) 3/8" bolts. Attention: The front leg pads can be
adjusted to provide a snug fit between the casing front and the casing
sides.
4. Attach (4) leveling bolts to the bottom of the (4) legs.
5. Align the 3/8" hole at the top of the leg with the 3/8" hole in the leg
pad. Attention: For proper positioning of the leg to the leg pad the
(2) 1-1/2" top edges of the leg must be placed flush and parallel to
the (2) edges on the leg pad. Attach leg to leg pad by inserting (1)
1" bolt through the leg pad and into the leg, secure bolt with 1/4"
nut.
6. Insert (2) 3/8" bolts into the (2) holes on the edges of the casing
sides. The bolts should only be threaded half-way into the holes in
order to allow for clearance when the casing back is attached to the
casing sides.
7. Refer to Figure 6, the rear cover has (4) keyholes for attachment to
the casing sides. Stand the casing sides on the floor with the (2)
bolts attached half-way into the edges of the rear cover positioned
at the rear. The large diameter holes in the keyholes of the rear cover
will be toward the floor. Working with one casing side at a time,
place the large diameter holes in the keyholes over and behind both
of the bolts at the same time. Push downward on the rear cover to
lock the keyholes into position behind the bolts. Finish tightening
both bolts to secure rear cover to casing side. Repeat this procedure
to secure rear cover to the second casing side.
Appliance Hardware Package Parts List
Part
Part
Quantity
Description
Number
Supplied
1/4-20 x 1" Phillips Head Bolt
R-3188
4
1/4-20 x 3/8" Phillips Head Bolt
R-3646
16
1/4-20 x 1/2" Leveling Bolt
R-3747
4
No. 10 x 1/2"
R-2737
6
Hex Washer Head Screw
1/4-20 Washer Head Nut
R-3185
4
Leg Pad "A" (see Figure 5)
CI-008
2
Leg Pad "B" (see Figure 5)
CI-009
2
1-1/4" x 1/2" Retaining Tab
CI-007
4
(see Figure 8)
1/4 x 9/32 Washer (Not Shown)
R-1150
8
Appliance Hardware Package (Figure 4)
Figure 4
Содержание CIBV-30-2
Страница 17: ...R 3450 Page 17 ...
Страница 19: ...R 3450 Page 19 ...
