background image

40916-0-0919

Page 17

 

1.  Push in gas control knob slightly and turn clockwise 

 to “OFF.” Do not force.

1.   STOP! Read the safety information above.

2.  Push in manual gas control knob slightly and turn clockwise 

 to “OFF”. Do not force.

3.  Wait ten (10) minutes to clear out any gas. Then smell for 

gas, including near the floor. If you smell gas, STOP! Follow 

“B” in the safety information above. If you do not smell gas, 

go to the next step.

4.  Find pilot - follow metal tube from gas control. The pilot is on 

the right side rear of the burner.

5.  Turn manual gas control knob counterclockwise 

 to 

“PILOT”.

6.  Push in control knob all the way and hold in. Immediately light 

the pilot with a match and the lighter rod that is provided with 

the burner. Continue to hold the control knob in for about one 

(1) minute after the pilot is lit. Release knob, and it will pop 

back up. Pilot should remain lit. If it goes out, repeat Steps 2 

through 6.

•  If knob does not pop up when released, stop and 

immediately  call  a  qualified  service  technician  or  gas 

supplier.

• 

If the pilot will not stay lit after several tries, turn the gas 

control knob to “OFF” and call your service technician or 

gas supplier.

7.  Turn manual gas control knob counterclockwise 

 to 

“ON”.

MANUAL LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

A.   This appliance has a pilot which must be lighted by hand. 

When lighting the pilot, follow these instructions exactly.

B.   BEFORE LIGHTING smell all around the appliance area 

for gas. Be sure to smell next to the floor because some 

gas is heavier than air and will settle on the floor.

 

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; 

 

do not use any phone in your building.

• 

Immediately call your gas supplier from a neighbor's 

phone. Follow the gas supplier's instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

C.   Use only your hand to push in or turn the gas control 

knob.  Never  use  tools.  If  the  knob  will  not  push  in  or 

turn by hand, don't try to repair it; call a qualified service 

technician. Force or attempted repair may result in a fire 

or explosion.

D.   Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect 

the appliance and to replace any part of the control system 

and any gas control which has been under water.

LIGHTING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

WARNING

 

•  Any glass doors shall be opened when the appliance is in operation.

•  A fireplace screen must be in place when the appliance is operating and the screen shall have an opening(s) for 

introduction of combustion air.

WARNING

 

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, 

personal injury or loss of life.

Содержание BFM18MTN





























Отзывы: